Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  P03402A  Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  P034511  Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground  P034515  Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open  P034531  Camshaft Position Sensor "A" Bank 2 No Signal  


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The camshaft timing gear assembly has a sensor plate for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground The output voltage of the VVT sensor (for intake camshaft) is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on SAE: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open The output voltage of the VVT sensor (for intake camshaft) is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on SAE: P0343
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range No VVT sensor (for intake camshaft) signal to ECM while cranking (2 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on SAE: P0340
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal No VVT sensor (for intake camshaft) signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on SAE: P0340
P034511 Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground The output voltage of the VVT sensor (for intake camshaft) is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on SAE: P0347
P034515 Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open The output voltage of the VVT sensor (for intake camshaft) is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on SAE: P0348
P034531 Camshaft Position Sensor "A" Bank 2 No Signal No VVT sensor (for intake camshaft) signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on SAE: P0345

HINT:

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P03351F


MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating, or if the rotation of the intake camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P034011, P034015, P03402A, P034031, P034511, P034515 or P034531.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A358820E04
0.333,2.25 0.792,2.448 0.458,0.198 10 false C64 0.354,2.417 3.083,2.635 2.729,0.219 10 false VVT Sensor (for Intake Camshaft of Bank 1) 1.5,1.917 1.958,2.115 0.458,0.198 10 false VVR- 1.417,1.385 1.875,1.583 0.458,0.198 10 false VVR+ 1.583,0.833 1.833,1 0.25,0.167 10 false VC 2.042,0.833 2.167,1 0.125,0.167 10 false 3 2.042,1.417 2.167,1.583 0.125,0.167 10 false 1 2.042,1.917 2.5,2.115 0.458,0.198 10 false 2 1.5,3.802 1.958,4 0.458,0.198 10 false VVL+ 1.5,4.333 1.958,4.531 0.458,0.198 10 false VVL- 0.333,4.635 0.792,4.833 0.458,0.198 10 false C65 0.333,4.833 3.042,5.031 2.708,0.198 10 false VVT Sensor (for Intake Camshaft of Bank 2) 4.458,0.833 4.917,1.031 0.458,0.198 10 false 87 4.792,0.833 5.25,1.031 0.458,0.198 10 false VCV1 4.458,1.385 4.917,1.583 0.458,0.198 10 false 89 4.792,1.385 5.25,1.583 0.458,0.198 10 false VV1+ 4.458,1.917 4.917,2.115 0.458,0.198 10 false 88 4.792,1.917 5.25,2.115 0.458,0.198 10 false VV1- 4.438,3.25 4.906,3.49 0.469,0.24 10 false 110 4.792,3.25 5.25,3.448 0.458,0.198 10 false VCV2 4.438,3.802 4.792,4 0.354,0.198 10 false 112 4.792,3.802 5.25,4 0.458,0.198 10 false VV2+ 4.438,4.333 4.792,4.531 0.354,0.198 10 false 111 4.792,4.333 5.25,4.531 0.458,0.198 10 false VV2- 5.333,5.219 5.792,5.417 0.458,0.198 10 false C92 5.333,5.417 5.792,5.615 0.458,0.198 10 false ECM 2,3.25 2.125,3.417 0.125,0.167 10 false 3 2,3.802 2.125,3.969 0.125,0.167 10 false 1 2,4.333 2.458,4.531 0.458,0.198 10 false 2 1.583,3.25 1.833,3.417 0.25,0.167 10 false VC

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT))

OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C64,C92,C65)Location & Routing

Click Connector(C64)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 1 Intake Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C65)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 2 Intake Side)

C64-1 (VVR+) - C92-89 (VV1+) Always Below 1 Ω
C64-2 (VVR-) - C92-88 (VV1-) Always Below 1 Ω
C65-1 (VVL+) - C92-112 (VV2+) Always Below 1 Ω
C65-2 (VVL-) - C92-111 (VV2-) Always Below 1 Ω
C64-1 (VVR+) or C92-89 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C64-2 (VVR-) or C92-88 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C65-1 (VVL+) or C92-112 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C65-2 (VVL-) or C92-111 (VV2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Check the VVT sensor (for intake camshaft) installation.

OK:

VVT sensor (for intake camshaft) is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL VVT SENSOR (FOR INTAKE CAMSHAFT)

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A385296C01
1.26,0.813 1.5,0.365 true 1.24,1.083 1.5,0.365 true 1.969,1.458 2.188,0.875 true 1.969,1.448 2.167,1.219 true 2.854,3.271 3.125,2.844 true 2.865,3.229 3.052,2.833 true 2.865,3.25 3.042,2.615 true 2.208,2.51 2.479,2.135 true 2.219,2.906 2.469,2.135 true 1.531,0.208 1.844,0.406 0.313,0.198 10 false *1 1.854,1.5 2.167,1.698 0.313,0.198 10 false *1 2.719,3.25 3.031,3.448 0.313,0.198 10 false *1 2.448,1.99 2.76,2.188 0.313,0.198 10 false *1
*1 Timing Mark


a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing sprockets are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)

NG

8.CHECK ENGINE MECHANICAL SYSTEM
6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the VVT sensor (for intake camshaft).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531 is output A
DTCs are not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P034011, P034015, P03402A, P034031, P034511, P034515 or P034531 is output A
DTCs are not output B


HINT:

If the engine does not start, replace the ECM.




A

B

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the VVT sensor (for exhaust camshaft) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C64,C92,C65)Location & Routing

Click Connector(C64)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 1 Intake Side)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C65)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor (Bank 2 Intake Side)

C64-3 (VC) - C92-87 (VCV1) Always Below 1 Ω
C65-3 (VC) - C92-110 (VCV2) Always Below 1 Ω
C64-3 (VC) or C92-87 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C65-3 (VC) or C92-110 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR