Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P044313  Evaporative Emission System Purge Control Valve "A" Circuit Open  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open Both of the following conditions (a) and (b) are met (1 trip detection logic)
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

EFI MAIN NO.1 relay

·

ECM


Comes on SAE: P0443

CONFIRMATION DRIVING PATTERN

A179391E35
1.525,1.949 1.755,2.124 0.23,0.175 10 [A] 2.846,1.949 3.077,2.124 0.23,0.175 10 [B] 3.892,3.005 4.123,3.18 0.23,0.175 10 [C] 4.574,1.338 4.805,1.512 0.23,0.175 10 [D] 5.097,3.005 5.328,3.18 0.23,0.175 10 [E] 0.509,2.071 0.887,2.255 0.378,0.184 10 Idling 4.224,2.524 5.01,2.838 0.786,0.314 10 10 minutes or more 2.594,2.524 3.38,2.838 0.786,0.314 10 15 minutes or more 1.31,2.524 2.105,2.689 0.795,0.166 10 Warming up 1.332,1.069 3.359,1.392 2.027,0.323 10 Between 40 km/h and 60 km/h 0.954,1.546 1.171,1.139 1.171,1.139 1.269,1.139 false 0.128,0.45 1.081,0.616 0.953,0.166 10 Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P044313.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P044313.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A488675E01
5.74,0.729 6.198,0.927 0.458,0.198 10 false PRG 5.385,0.823 5.844,1.021 0.458,0.198 10 false C92 5.729,2 6.344,2.198 0.615,0.198 10 false MREL 5.438,2.01 5.75,2.208 0.313,0.198 10 false B2 3.969,1.135 4.427,1.333 0.458,0.198 10 false C70 4.042,1.313 5.417,1.51 1.375,0.198 10 false Purge VSV 5.052,0.698 5.208,0.896 0.156,0.198 10 false 2 3.906,0.719 4.063,0.917 0.156,0.198 10 false 1 2.823,0.99 4.51,1.188 1.688,0.198 10 false EFI-B NO. 2 2.271,0.729 2.427,0.927 0.156,0.198 10 false 3 1.604,0.729 1.76,0.927 0.156,0.198 10 false 5 1.604,1.229 1.76,1.427 0.156,0.198 10 false 2 2.271,1.219 2.427,1.417 0.156,0.198 10 false 1 0.594,0.99 2.74,1.188 2.146,0.198 10 false EFI MAIN NO. 1 0.552,2.344 2.542,2.542 1.99,0.198 10 false SUB R/B-NO. 1 0.656,2.969 1.729,3.167 1.073,0.198 10 false Battery 6.125,2.979 6.583,3.177 0.458,0.198 10 false ECM 5.479,0.615 5.792,0.813 0.313,0.198 10 false 82 5.521,1.813 5.677,2.01 0.156,0.198 10 false 6 1.5,1.604 3.646,1.802 2.146,0.198 10 false EFI MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
A348207C01
0.833,0.417 1.667,0.833 true 2.833,1.25 2.417,1.5 true 0.583,0.333 0.833,0.583 0.25,0.25 10 true *1 2.833,1.167 3.083,1.417 0.25,0.25 10 true *2
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)


a.

Disconnect the fuel vapor feed hose (charcoal canister side) of the purge VSV.


b.

Start the engine.


c.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1
OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV
a.

Inspect the purge VSV.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>PURGE VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI MAIN NO.1 RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI MAIN NO.1 RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the EFI MAIN NO.1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C70)Location & Routing

Click Connector(C70)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Vacuum Switching Valve Assembly (Purge)

C70-1 - 3 (EFI MAIN NO.1 relay) Always Below 1 Ω
C70-1 or 3 (EFI MAIN NO.1 relay) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR