Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P061512  Starter Relay Circuit Circuit Short To Battery  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P061512 Starter Relay Circuit Circuit Short To Battery All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Park/neutral position switch assembly

·

ST NO. 1 relay circuit

·

ECM


Comes on SAE: P0617

CONFIRMATION DRIVING PATTERN

A231469E24
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P061512.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A488678E01
1.802,0.927 2.052,1.125 0.25,0.198 10 false 15 0.052,2.646 2.917,2.885 2.865,0.24 10 false Certification ECU (Smart Key ECU Assembly) 0.583,4.354 1.667,4.583 1.083,0.229 10 false SUB R/B-NO.1 0.729,6.802 1.25,7.021 0.521,0.219 10 false Battery 5.354,0.844 5.813,1.042 0.458,0.198 10 false 41 5.708,1.604 6.167,1.802 0.458,0.198 10 false NSW 3.094,2.281 3.552,2.479 0.458,0.198 10 false C34 3.094,2.469 5.573,2.677 2.479,0.208 10 false Park/Neutral Position Switch Assembly 4.563,1.969 4.823,2.219 0.26,0.25 10 false 4 3.531,1.99 3.708,2.188 0.177,0.198 10 false 5 4.313,1.99 4.49,2.188 0.177,0.198 10 false B 3.729,2 3.906,2.198 0.177,0.198 10 false L 5.344,3.542 5.802,3.74 0.458,0.198 10 false 16 5.698,3.646 6.156,3.844 0.458,0.198 10 false STA 5.354,1.063 5.813,1.26 0.458,0.198 10 false B2 3.292,4.615 3.885,4.802 0.594,0.188 10 false ST NO.1 1.323,3.427 1.917,3.615 0.594,0.188 10 false ST NO.1 3.021,4.115 3.198,4.313 0.177,0.198 10 false 2 3.021,5.073 3.198,5.271 0.177,0.198 10 false 1 2.542,4.115 2.719,4.313 0.177,0.198 10 false 5 2.521,5.073 2.698,5.271 0.177,0.198 10 false 3 1.563,6.719 2.656,6.917 1.094,0.198 10 false Starter 1.708,5.667 2.167,5.865 0.458,0.198 10 false C101 1.031,5.917 1.344,6.115 0.313,0.198 10 false C99 1.729,5.458 1.906,5.656 0.177,0.198 10 false 1 1.125,5.688 1.302,5.885 0.177,0.198 10 false 1 0.052,2.458 2.917,2.698 2.865,0.24 10 false I40 6.094,4.969 6.552,5.167 0.458,0.198 10 false ECM 1.469,1.063 1.927,1.26 0.458,0.198 10 false NE 1.302,1.573 1.76,1.771 0.458,0.198 10 false STAR 1.396,2.104 1.854,2.302 0.458,0.198 10 false STA 1.813,1.458 2.063,1.656 0.25,0.198 10 false 10 1.844,1.99 2.094,2.188 0.25,0.198 10 false 3 5.698,1.042 6.156,1.24 0.458,0.198 10 false NEO 5.354,1.365 5.813,1.563 0.458,0.198 10 false 48 5.344,3.781 5.802,3.979 0.458,0.198 10 false B2 5.313,1.594 5.771,1.792 0.458,0.198 10 false C92

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.43 mph) or more.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter SW Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P061512)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P061512)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P061512 is output A
DTCs are not output B




A

B

END