Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A373204E89
1.26,0.885 1.875,1.083 0.615,0.198 10 false CANH 1.292,1.594 1.906,1.792 0.615,0.198 10 false CANL 2.833,0.875 3.448,1.073 0.615,0.198 10 false CA3H 5.51,1.573 6.125,1.771 0.615,0.198 10 false CANL 5.51,0.865 6.125,1.063 0.615,0.198 10 false CANH 2.844,1.573 3.458,1.771 0.615,0.198 10 false CA3L 3.927,0.875 4.542,1.073 0.615,0.198 10 false CA4H 3.948,1.583 4.563,1.781 0.615,0.198 10 false CA4L 0.927,3.219 3.042,3.51 2.115,0.292 10 false : CAN Communication Line 2.896,2.25 4.438,2.5 1.542,0.25 10 false Network Gateway ECU 0.083,2.25 2.021,2.573 1.938,0.323 10 false Combination Meter Assembly 6.073,2.26 6.583,2.542 0.51,0.281 10 false ECM 6.073,2.104 6.688,2.302 0.615,0.198 10 false B2 2.906,2.094 3.521,2.292 0.615,0.198 10 false I42 0.094,2.094 0.708,2.292 0.615,0.198 10 false I5 1.75,0.708 2.365,0.906 0.615,0.198 10 false 13 1.729,1.417 2.344,1.615 0.615,0.198 10 false 29 2.604,0.708 3.219,0.906 0.615,0.198 10 false 30 2.604,1.417 3.219,1.615 0.615,0.198 10 false 29 4.365,0.698 4.979,0.896 0.615,0.198 10 false 26 4.365,1.417 4.979,1.615 0.615,0.198 10 false 25 5.26,0.698 5.875,0.896 0.615,0.198 10 false 11 5.281,1.396 5.896,1.594 0.615,0.198 10 false 19

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B




A

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Turn the ignition switch to ON.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the ignition switch to ON.


b.

Enter the following menus: System Select / Health Check.


c.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
a.

Turn the ignition switch to ON.


b.

Check the status of the MIL while performing the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Warning
50004 409 64
Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY