Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E27
1.625,0.823 2.938,1.115 1.313,0.292 10 false from EFI-B Fuse 0.99,1.177 2.74,1.427 1.75,0.25 10 false from EFI-MAIN NO.1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.573,3.083 2.438,0.438 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

VC Power Source Circuit
A488666E03
0.521,0.479 0.979,0.677 0.458,0.198 10 false C69 0.531,2.688 0.99,2.885 0.458,0.198 10 false C64 0.552,4.01 1.01,4.208 0.458,0.198 10 false C66 0.583,5.854 1.042,6.052 0.458,0.198 10 false C65 0.594,7.167 1.052,7.365 0.458,0.198 10 false C67 2.844,0.385 3.302,0.583 0.458,0.198 10 false 5 2.844,1.104 3.302,1.302 0.458,0.198 10 false 6 2.854,1.469 3.313,1.667 0.458,0.198 10 false 4 2.844,0.729 3.302,0.927 0.458,0.198 10 false 3 2.865,2.729 3.323,2.927 0.458,0.198 10 false 3 2.875,3.99 3.333,4.188 0.458,0.198 10 false 3 2.865,3.073 3.323,3.271 0.458,0.198 10 false 2 2.885,4.406 3.344,4.604 0.458,0.198 10 false 2 2.854,6.219 3.313,6.417 0.458,0.198 10 false 2 2.854,5.854 3.313,6.052 0.458,0.198 10 false 3 2.865,3.427 3.323,3.625 0.458,0.198 10 false 1 2.896,4.75 3.354,4.948 0.458,0.198 10 false 1 2.854,6.573 3.313,6.771 0.458,0.198 10 false 1 2.844,7.917 3.302,8.115 0.458,0.198 10 false 1 2.844,7.552 3.302,7.75 0.458,0.198 10 false 2 2.833,7.177 3.292,7.375 0.458,0.198 10 false 3 0.521,0.656 2.396,1.073 1.875,0.417 10 false Throttle with Throttle Position Sensor Body Assembly 0.542,2.865 1.948,3.594 1.406,0.729 10 false VVT Sensor (for Intake Camshaft of Bank 1) 0.563,4.188 2.104,4.917 1.542,0.729 10 false VVT Sensor (for Exhaust Camshaft of Bank 1) 0.573,6.063 1.979,6.792 1.406,0.729 10 false VVT Sensor (for Intake Camshaft of Bank 2) 0.594,7.354 2.135,8.083 1.542,0.729 10 false VVT Sensor (for Exhaust Camshaft of Bank 2) 2.563,0.479 3.021,0.677 0.458,0.198 10 false VC 2.573,0.833 3.031,1.031 0.458,0.198 10 false E2 2.479,1.198 2.938,1.396 0.458,0.198 10 false VTA 2.417,1.563 2.875,1.76 0.458,0.198 10 false VTA2 2.531,2.792 2.99,2.99 0.458,0.198 10 false VC 2.417,3.177 2.875,3.375 0.458,0.198 10 false VVR- 2.385,3.531 2.844,3.729 0.458,0.198 10 false VVR+ 2.49,4.125 2.948,4.323 0.458,0.198 10 false VC2 2.531,4.458 2.99,4.656 0.458,0.198 10 false EX- 2.49,4.865 2.948,5.063 0.458,0.198 10 false EX+ 2.531,5.958 2.99,6.156 0.458,0.198 10 false VC 2.438,6.302 2.896,6.5 0.458,0.198 10 false VVL- 2.406,6.688 2.865,6.885 0.458,0.198 10 false VVL+ 2.49,7.281 2.948,7.479 0.458,0.198 10 false VC2 2.521,7.635 2.979,7.833 0.458,0.198 10 false EX- 2.5,8.021 2.958,8.219 0.458,0.198 10 false EX+ 5.271,8.021 5.729,8.219 0.458,0.198 10 false EV2+ 5.75,8.438 6.208,8.635 0.458,0.198 10 false ECM 5.271,6.698 5.729,6.896 0.458,0.198 10 false VV2+ 5.271,6.26 5.729,6.458 0.458,0.198 10 false VV2- 5.26,5.875 5.719,6.073 0.458,0.198 10 false VCV2 5.292,4.854 5.75,5.052 0.458,0.198 10 false EV1+ 5.302,3.583 5.76,3.781 0.458,0.198 10 false VV1+ 5.323,3.083 5.781,3.281 0.458,0.198 10 false VV1- 5.292,2.719 5.75,2.917 0.458,0.198 10 false VCV1 5.271,1.219 5.729,1.417 0.458,0.198 10 false VTA1 6.292,0.219 6.75,0.417 0.458,0.198 10 false 5 V 5.281,0.385 5.74,0.583 0.458,0.198 10 false VCTA 5.271,1.573 5.729,1.771 0.458,0.198 10 false VTA2 4.938,0.313 5.271,0.51 0.333,0.198 10 false 125 4.938,0.677 5.25,0.875 0.313,0.198 10 false 124 4.948,1.042 5.281,1.24 0.333,0.198 10 false 126 4.948,1.417 5.25,1.615 0.302,0.198 10 false 101 5.021,2.656 5.333,2.896 0.313,0.24 10 false 87 5.01,3.021 5.323,3.26 0.313,0.24 10 false 88 5.01,3.396 5.323,3.635 0.313,0.24 10 false 89 5.021,4.677 5.333,4.917 0.313,0.24 10 false 90 4.948,5.802 5.26,6.042 0.313,0.24 10 false 110 4.948,6.167 5.26,6.406 0.313,0.24 10 false 111 4.938,6.542 5.25,6.781 0.313,0.24 10 false 112 4.938,7.865 5.25,8.104 0.313,0.24 10 false 113 4.958,4.875 5.271,5.115 0.313,0.24 10 false C92 4.927,3.583 5.24,3.823 0.313,0.24 10 false C92 4.938,3.208 5.25,3.448 0.313,0.24 10 false C92 4.938,2.844 5.25,3.083 0.313,0.24 10 false C92 4.938,1.594 5.25,1.833 0.313,0.24 10 false C92 4.938,1.229 5.25,1.469 0.313,0.24 10 false C92 4.927,0.865 5.24,1.104 0.313,0.24 10 false C92 4.927,0.5 5.24,0.74 0.313,0.24 10 false C92 5.281,0.74 5.74,0.938 0.458,0.198 10 false ETA 4.938,8.042 5.25,8.281 0.313,0.24 10 false C92 4.948,5.979 5.26,6.219 0.313,0.24 10 false C92 4.938,6.344 5.25,6.583 0.313,0.24 10 false C92 4.938,6.708 5.25,6.948 0.313,0.24 10 false C92

A488667E01
5.323,0.271 5.938,0.469 0.615,0.198 10 false VCPA 5.323,0.646 5.938,0.844 0.615,0.198 10 false VCP2 5.313,1.01 5.927,1.208 0.615,0.198 10 false EPA 5.313,1.385 5.927,1.583 0.615,0.198 10 false EPA2 5.323,1.833 5.938,2.031 0.615,0.198 10 false VPA 5.323,2.198 5.938,2.396 0.615,0.198 10 false VPA2 5.323,2.865 5.938,3.063 0.615,0.198 10 false VCAI 5.323,3.25 5.938,3.448 0.615,0.198 10 false ETHW 5.333,3.719 5.948,3.917 0.615,0.198 10 false PSP 5.333,5.281 5.646,5.479 0.313,0.198 10 false AIP 5.323,6.594 5.781,6.792 0.458,0.198 10 false AIP2 4.958,0.198 5.271,0.396 0.313,0.198 10 false 55 4.958,0.563 5.271,0.76 0.313,0.198 10 false 58 4.969,0.927 5.281,1.125 0.313,0.198 10 false 54 5.01,5.063 5.323,5.26 0.313,0.198 10 false 73 4.969,1.667 5.281,1.865 0.313,0.198 10 false 53 4.969,2.021 5.281,2.219 0.313,0.198 10 false 56 4.99,2.792 5.302,2.99 0.313,0.198 10 false 75 4.979,3.542 5.292,3.74 0.313,0.198 10 false 76 4.938,3.177 5.25,3.375 0.313,0.198 10 false 123 4.979,1.302 5.292,1.5 0.313,0.198 10 false 57 4.979,6.448 5.292,6.646 0.313,0.198 10 false 72 0.51,0.521 2.083,0.979 1.573,0.458 10 false Accelerator Pedal (with Sensor) Rod Assembly 0.542,3.083 1.865,3.5 1.323,0.417 10 false Power Steering Oil Pressure Sensor 0.5,4.708 2.292,5.031 1.792,0.323 10 false Emission Control Valve Set 0.469,6.083 1.927,6.552 1.458,0.469 10 false No. 2 Emission Control Valve Set 2.406,0.365 3.021,0.563 0.615,0.198 10 false VCPA 2.406,0.729 3.021,0.927 0.615,0.198 10 false VCP2 2.49,1.094 3.104,1.292 0.615,0.198 10 false EPA 2.417,1.469 3.031,1.667 0.615,0.198 10 false EPA2 2.49,1.823 3.104,2.021 0.615,0.198 10 false VPA 2.427,2.188 3.042,2.385 0.615,0.198 10 false VPA2 2.594,2.99 3.208,3.188 0.615,0.198 10 false VC 2.594,3.354 2.906,3.552 0.313,0.198 10 false E2 2.5,3.698 3.115,3.896 0.615,0.198 10 false PSP 2.615,4.542 3.229,4.74 0.615,0.198 10 false VC 2.594,4.906 2.906,5.104 0.313,0.198 10 false E2 2.5,5.896 2.958,6.094 0.458,0.198 10 false VC2 2.594,5.26 3.208,5.458 0.615,0.198 10 false AIP 2.51,6.25 3.125,6.448 0.615,0.198 10 false E22 2.469,6.615 3.083,6.813 0.615,0.198 10 false AIP2 2.885,0.281 3.042,0.479 0.156,0.198 10 false 4 2.875,0.656 3.031,0.854 0.156,0.198 10 false 1 2.875,1.01 3.031,1.208 0.156,0.198 10 false 5 2.875,1.375 3.031,1.573 0.156,0.198 10 false 2 2.875,1.74 3.031,1.938 0.156,0.198 10 false 6 2.875,2.104 3.031,2.302 0.156,0.198 10 false 3 2.885,2.885 3.042,3.083 0.156,0.198 10 false 1 2.885,3.24 3.042,3.438 0.156,0.198 10 false 3 2.875,3.583 3.031,3.781 0.156,0.198 10 false 2 2.927,4.406 3.083,4.604 0.156,0.198 10 false 2 2.927,4.76 3.083,4.958 0.156,0.198 10 false 4 2.938,5.146 3.094,5.344 0.156,0.198 10 false 3 2.865,5.813 3.021,6.01 0.156,0.198 10 false 2 5.917,8 6.375,8.198 0.458,0.198 10 false ECM 0.521,0.354 0.833,0.552 0.313,0.198 10 false B17 4.958,0.375 5.271,0.573 0.313,0.198 10 false B2 4.948,0.74 5.26,0.938 0.313,0.198 10 false B2 4.969,1.479 5.281,1.677 0.313,0.198 10 false B2 4.958,1.844 5.271,2.042 0.313,0.198 10 false B2 4.958,2.198 5.271,2.396 0.313,0.198 10 false B2 4.969,1.115 5.281,1.313 0.313,0.198 10 false B2 0.542,2.917 0.854,3.115 0.313,0.198 10 false C50 4.938,3.365 5.25,3.563 0.313,0.198 10 false C92 4.917,2.99 5.229,3.188 0.313,0.198 10 false C92 4.927,3.729 5.24,3.927 0.313,0.198 10 false C92 0.5,4.51 0.813,4.708 0.313,0.198 10 false C94 4.917,5.271 5.229,5.469 0.313,0.198 10 false C92 0.469,5.896 0.781,6.094 0.313,0.198 10 false C95 2.885,6.156 3.042,6.354 0.156,0.198 10 false 4 2.885,6.531 3.042,6.729 0.156,0.198 10 false 3 4.938,6.625 5.25,6.823 0.313,0.198 10 false C92

For the circuit diagram of the ECM power source circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Turn the ignition switch to ON.


b.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (EFI-B NO.1 FUSE)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (EFI-B NO.1 FUSE)
a.
A488868C01
1.646,2.083 1.948,2.781 true 0.135,0.229 0.448,0.427 0.313,0.198 10 false *a 1.917,2.844 2.229,3.042 0.313,0.198 10 false *1
*a Engine Room Relay Block No. 2
*1 EFI-B NO. 1 Fuse


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI-B NO.1 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the engine room relay block No. 2.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with throttle position sensor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle with throttle position sensor body assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))

B

REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)

6.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)

7.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1)

8.CHECK CONNECTION BETWEEN GTS AND ECM (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (EMISSION CONTROL VALVE SET (FOR BANK 1))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2)

9.CHECK CONNECTION BETWEEN GTS AND ECM (EMISSION CONTROL VALVE SET (FOR BANK 1))
a.

Disconnect the emission control valve set (for bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (EMISSION CONTROL VALVE SET (FOR BANK 2))

B

10.CHECK CONNECTION BETWEEN GTS AND ECM (EMISSION CONTROL VALVE SET (FOR BANK 2))
a.

Disconnect the emission control valve set (for bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (POWER STEERING OIL PRESSURE SWITCH)

B

11.CHECK CONNECTION BETWEEN GTS AND ECM (POWER STEERING OIL PRESSURE SWITCH)
a.

Disconnect the power steering oil pressure switch connector.


b.

Turn the ignition switch to ON.


c.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

12.CHECK HARNESS AND CONNECTOR

B

12.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle with throttle position sensor body assembly connector.


b.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


c.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


d.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


e.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


f.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


g.

Disconnect the emission control valve set (for bank 1) connector (with Secondary Air Injection System).


h.

Disconnect the emission control valve set (for bank 2) connector (with Secondary Air Injection System).


i.

Disconnect the power steering oil pressure sensor connector.


j.

Disconnect the ECM connector.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C92,B2)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

C92-125 (VCTA) - Body ground and other terminals Always 10 kΩ or higher
B2-55 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
B2-58 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
C92-87 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C92-110 (VCV2) - Body ground and other terminals Always 10 kΩ or higher
C92-75 (VCAI) - Body ground and other terminals Always 10 kΩ or higher
2 (EFI-B NO. 1 fuse) - B2-2 (+B) Always Below 1 Ω
2 (EFI-B NO. 1 fuse) - B2-3 (+B2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR