Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Rough Idling  


DESCRIPTION

Problem Symptom Suspected Area Trouble Area
·

Engine speed fluctuation due to abnormal combustion

·

Idle speed too low or high


Strong engine vibration due to above symptoms
·

Ignition malfunction

·

Deviation in air fuel ratio (Excessive or insufficient intake air volume or fuel supply)

·

Insufficient compression

·

Changes in load from another system


Ignition system
·

Spark plug

·

Ignition coil assembly


Fuel system
·

Fuel injector assembly

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

Purge VSV system

·

Fuel quality (existence of foreign matter, degradation)


Intake and exhaust systems
·

Mass air flow meter

·

Intake system

(Air leaks or deposit accumulation)

·

Throttle with throttle position sensor body assembly

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Camshaft timing oil control valve assembly

·

Variable Valve Timing system (VVT system)

·

Brake booster assembly


Other control systems
·

ECM

·

Wire harness or connector

·

Knock control sensor

·

Engine coolant temperature sensor


Engine
·

Water inlet sub-assembly with thermostat

·

Engine assembly

·

Engine mount


High load from another system
·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system



HINT:
·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Make sure to reproduce the conditions present when the malfunction occurred.

·

Using the GTS, read the Data List to confirm the engine operating conditions. This information can be useful when troubleshooting.

·

If the problem symptoms do not recur, attempt to reproduce the symptoms and conditions when the malfunction occurred based on the result of the customer problem analysis. Place the priority on confirming the symptoms.



SYMPTOM AND CAUSE OF SYSTEM MALFUNCTION


HINT:

The following are descriptions of the characteristics of each system malfunction. After understanding the link between the causes and symptoms, perform the inspection of each component. Even if the problem symptom does not recur, signs of the malfunction may be found in the Data List.


a.

Ignition system

Spark plug
Main cause of malfunction Performance degradation (wear, existence of foreign matter, etc.)
Symptom Engine speed fluctuation due to abnormal combustion
Data List Misfire Count Cylinder #1 to #6
HINT:

If the spark plug of the malfunctioning cylinder is abnormally wet with fuel, a leaking fuel injector assembly is suspected.



Ignition coil assembly
Main cause of malfunction Internal malfunction
Problem symptom Engine speed fluctuation due to abnormal combustion
Data List Misfire Count Cylinder #1 to #6


b.

Fuel system

Fuel injector assembly
Main cause of malfunction Blockage
Problem symptom
·

Engine speed fluctuation due to abnormal combustion

·

Idle speed too low or high


Data List
·

Short FT B1S1 (B2S1)

·

Long FT B1S1 (B2S1)

·

Fuel System Status Bank 1 (Bank 2)

·

Target Air-Fuel Ratio

·

A/F (O2) Lambda Sensor B1S1 (B2S1)

·

A/F Learn Value Idle Bank 1 (Bank 2)

·

A/F Learn Value Low Bank 1 (Bank 2)

·

A/F Learn Value Mid No.1 Bank 1 (Bank 2)

·

A/F Learn Value Mid No.2 Bank 1 (Bank 2)

·

A/F Learn Value High Bank 1 (Bank 2)

·

Total FT Bank 1 (Bank 2)


HINT:

If the engine malfunction disappears when the fuel injection volume is increased or decreased using the Control the Injection Volume, the respective cylinder may be malfunctioning.



Fuel system
HINT:

If the air fuel ratio becomes lean only when the engine is running under a high load and at a high engine speed, clogging of the fuel pump or fuel filter is suspected.



Fuel quality
Main cause of malfunction
·

Fuel degradation due to age or water contamination

·

Low fuel quality

·

Addition of fuel additive


Problem symptom
·

Engine speed fluctuation due to abnormal combustion

·

Idle speed too low or high

·

Engine is difficult to start




c.

Intake and exhaust systems

Mass air flow meter sub-assembly
Main cause of malfunction Performance degradation (existence of foreign matter, etc.)
Problem symptom Lack of power
Data List Mass Air Flow Sensor
HINT:

If the value of the Data List item "Mass Air Flow Sensor" is abnormal, a malfunction of the mass air flow meter sub-assembly is suspected.



Throttle system
Main cause of malfunction Inappropriate trim volume adjustment due to accumulation of deposits
Problem symptom
·

Engine speed fluctuation due to abnormal combustion

·

Idle speed too low or high


Data List
·

ISC F/B Learn Torque

·

ISC Total AUXS Torque

·

ISC F/B Torque

·

Sum of ISC F/B Torque (Recent)

·

ISC AUXS Torque (Alternator)

·

ISC AUXS Torque (Air Conditioner)

·

Throttle Air Flow F/B Value



Air fuel ratio sensor, Heated oxygen sensor
Main cause of malfunction Deviation in sensor characteristics
Problem symptom Abnormal combustion due to deviation of actual air fuel ratio from calculated ratio
Data List
·

A/F (O2) Sensor Voltage B1S1 (B2S1)

·

O2 Sensor Voltage B1S2 (B2S2)

·

Fuel System Status Bank 1 (Bank 2)




d.

Engine

Engine assembly
Main cause of malfunction
·

Compression loss

·

Accumulation of deposits

(Combustion chamber, intake valve or intake manifold)


Problem symptom
·

Engine speed fluctuation due to abnormal combustion

·

Idle speed too low or high

·

Hesitation during acceleration or stalling


HINT:
·

If deposits have accumulated in the combustion chamber or on an intake valve, the engine may stall when deposits are caught on an intake valve.

·

When performing the Active Test "Check the Cylinder Compression", if the speed of one cylinder is higher than the others, the cylinder may have a compression loss.

·

If deposits accumulate on the intake valves, the supply of fuel may be delayed due to adherence of the fuel to the deposits, causing a rough idle.






Data List Items Related to Rough Idling


HINT:

Depending on the vehicle model, the applicable Data List items may vary. Data List items other than the ones used in the diagnostic procedure are for reference only.

·

ISC F/B Learn Torque

·

ISC Total AUXS Torque

·

ISC F/B Torque

·

Sum of ISC F/B Torque (Recent)

·

ISC AUXS Torque (Alternator)

·

ISC AUXS Torque (Air Conditioner)

·

Throttle Air Flow F/B Value

·

Short FT B1S1 (B2S1)

·

Long FT B1S1 (B2S1)

·

Total FT Bank 1 (Bank 2)

·

Fuel System Status Bank 1 (Bank 2)

·

Target Air-Fuel Ratio

·

A/F (O2) Lambda Sensor B1S1 (B2S1)

·

A/F Learn Value Idle Bank 1 (Bank 2)

·

A/F Learn Value Low Bank 1 (Bank 2)

·

A/F Learn Value Mid No.1 Bank 1 (Bank 2)

·

A/F Learn Value Mid No.2 Bank 1 (Bank 2)

·

A/F Learn Value High Bank 1 (Bank 2)

·

Mass Air Flow Sensor

·

Misfire Count Cylinder #1 (to #6)

·

A/F (O2) Sensor Voltage B1S1 (B2S1)

·

O2 Sensor Voltage B1S2 (B2S2)

·

Engine Speed




PROCEDURE

1.INTERVIEW THE CUSTOMER
a.

Interview the customer for details about the conditions when the rough idle occurred.

HINT:

Depending on the conditions when the rough idle occurred, a malfunction in one of the following areas is suspected.

Problem Symptom Suspected Area
Hesitation or lack of power occurs during acceleration, regardless of whether engine is cold or warm
·

For low mileage vehicles (ODO reading of less than approximately 20000 km or yearly mileage of less than 2000 km): Fuel quality (degradation, water contamination, etc.)

·

For high mileage vehicles (ODO reading of more than approximately 150000 km): Excessively lean air fuel ratio during acceleration due to deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve or adherence of fuel to the deposits

·

Abnormal mass air flow meter sub-assembly output due to existence of foreign matter

·

Decrease in fuel injector assembly injection volume due to low quality fuel


Engine stalls or is difficult to start immediately after engine stalled, regardless of whether engine is cold or warm Deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve
·

When decelerating vehicle to a stop, engine speed drops momentarily and vehicle shudders

·

When moving shift lever from N to D or R, or operating air conditioning system or any electrical components, engine speed fluctuates and vehicle shudders


Temporary deviation in the electrical throttle system idle speed control due to external factors (fuel quality, air conditioning system (environmental causes or low refrigerant pressure), charging system (battery deterioration or low power generation by the alternator) or brake booster system)



Result:
Proceed to
NEXT



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON.


b.

Perform a road test.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTC is output
(DTCs other than P160300, P160400 or P160500 are output)
B



A

3.SYMPTOM CONFIRMATION

B

3.SYMPTOM CONFIRMATION
a.

Check if the problem symptoms reported in the customer problem analysis recur.

HINT:

If the problem symptoms do not recur, attempt to reproduce the conditions when the malfunction occurred based on the result of the customer problem analysis.



Result:
Result Proceed to
The problem symptom recurs A
The problem symptom does not recur (occurred in the past) B



A

4.READ VALUE USING GTS (SHORT FT B1S1 (B2S1) AND LONG FT B1S1 (B2S1))

B

4.READ VALUE USING GTS (SHORT FT B1S1 (B2S1) AND LONG FT B1S1 (B2S1))
a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Short FT B1S1
Short FT B2S1
Long FT B1S1
Long FT B2S1
50003 372 207,508,209,509
Result:
Data List Result Proceed to
Short FT B1S1 (B2S1) + Long FT B1S1 (B2S1) -15% or higher, or less than 15% A
Other than above B


HINT:
·

"Total FT Bank 1 (Bank 2)" is used to detect an abnormal air fuel ratio. As the value of "Total FT Bank 1 (Bank 2)" is corrected by the ECM before it is displayed in the Data List, the displayed value may not be equal to the sum of the measured "Short FT B1S1 (B2S1)" and "Long FT B1S1 (B2S1)".

·

An abnormally lean or rich tendency can be checked by reading the following Data List items: A/F Learn Value Idle Bank 1 (Bank 2), A/F Learn Value Low Bank 1 (Bank 2), A/F Learn Value Mid No.1 Bank 1 (Bank 2), A/F Learn Value Mid No.2 Bank 1 (Bank 2), A/F Learn Value High Bank 1 (Bank 2). (For vehicles equipped with a V type engine, check that both banks have the same correction tendency.) If the correction of either bank is -15% or less or +15% or higher, the air fuel ratio sensor or heated oxygen sensor of that bank may be malfunctioning.

·

The following may cause a lean air fuel ratio (an operating range in which the air fuel ratio learned value correction is +15% or higher):

(a)

Decrease in fuel injector assembly injection volume

(b)

Decrease in mass air flow meter sub-assembly output (due to existence of foreign matter)

(c)

Air leaks in intake system after mass air flow meter sub-assembly

(d)

Decrease in fuel pressure (at fuel filter, fuel pump or fuel pressure regulator assembly)


·

On vehicles which the learning value for each operating range can be checked, if the value of "A/F Learn Value High Bank 1 (Bank 2)" only is corrected to the positive side, a malfunction in the fuel system (clogging of the fuel pump or fuel filter) is suspected.

·

On vehicles which the learning value for each operating range can be checked, if the value of "A/F Learn Value Idle Bank 1 (Bank 2)" or "A/F Learn Value Low Bank 1 (Bank 2)" only is corrected to the positive side, an air leak after the mass air flow meter sub-assembly is suspected.

·

The following may cause a rich air fuel ratio (an operating range in which the air fuel ratio learned value correction is -15% or less):

(a)

Increase in the fuel injector assembly injection volume

(b)

Purge VSV system






A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
a.

Start the engine.

HINT:

Reproduce the vehicle conditions when the malfunction occurred. (such as after the engine is warmed up or after a cold start).



b.

According to the display on the GTS, perform the Active Test and check for a malfunctioning cylinder.

Powertrain > Engine > Active Test
Active Test Display
Control the Select Cylinder Fuel Cut
Data List Display
Engine Speed
50004 372 42014 211
HINT:
·

Perform fuel-cut for each cylinder and check the change in the engine speed.

·

If the engine speed of a cylinder does not change while performing the Active Test, it can be determined that the cylinder is malfunctioning.

·

If the engine speed of all cylinders change while performing the Active Test, it can be determined that multiple cylinders are malfunctioning.

·

A cylinder for which the Data List item "Misfire Count Cylinder #1 (to #6)" increases may be malfunctioning.




Result:
Result Proceed to
One cylinder is malfunctioning A
Multiple or all cylinders are malfunctioning, or the malfunctioning cylinder cannot be determined. B



A

6.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

B

12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
6.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

If the vehicle does not support the Active Test "Check the Cylinder Compression", measure the compression pressure. If the compression pressure is normal, go to step 7.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed Cylinder #1
Engine Speed Cylinder #2
Engine Speed Cylinder #3
Engine Speed Cylinder #4
Engine Speed Cylinder #5
Engine Speed Cylinder #6
Average Engine Speed of All Cylinder
50004 372 42016 493,494,495,496,497,498,492
HINT:
·

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

·

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.




e.

Crank the engine for about 10 seconds.


f.

Monitor the engine speed (Engine Speed Cylinder #1 to #6 and Average Engine Speed of All Cylinder) displayed on the GTS.

HINT:

At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.

·

Use a fully-charged battery.




g.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:
·

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

·

When performing the Active Test, DTC P160400 (Startability Malfunction) may be stored.

·

After performing the Active Test, make sure to check and clear DTCs.




h.

Read the value.

HINT:
·

If the value of Data List item "Engine Speed Cylinder #1 to #6" of a cylinder is higher than other cylinders, the cylinder may be malfunctioning.

·

If the value of Data List item "Engine Speed Cylinder #1 to #6" is high for only one cylinder, compression loss is suspected.




Result:
Result Proceed to
There is no variation in "Engine Speed Cylinder #1 to #6"
(All cylinders display approximately the same value for "Engine Speed Cylinder #1 to #6")
A
There is variation in "Engine Speed Cylinder #1 to #6"
(Only one cylinder displays a value for "Engine Speed Cylinder #1 to #6" that differs considerably)
B



A

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

B

11.CHECK CYLINDER COMPRESSION PRESSURE
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.


b.

Idle the engine.


c.

According to the display on the GTS, perform the Active Test and check the vehicle conditions when increasing and decreasing the fuel injection volume.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume
50004 372 7
HINT:

Change the fuel injection volume between the minimum and maximum range of correction (e.g. -12.5% to 12.5%).



Result:
Result Proceed to
Malfunction is still present even if the fuel injection volume is changed A
Malfunction disappears when the fuel injection volume is changed B



A

8.CHECK IGNITION SYSTEM

B

10.REPLACE FUEL INJECTOR ASSEMBLY
8.CHECK IGNITION SYSTEM
a.

Check the ignition system.

HINT:
·

Interchange the ignition coil assembly and spark plug of the malfunctioning cylinder with those of a known good cylinder and check if the malfunctioning cylinder returns to normal.

·

If the spark plug of the malfunctioning cylinder is abnormally wet with fuel even after the ignition coil assembly and spark plug are replaced, a leaking fuel injector assembly is suspected.




Result:
Result Proceed to
The malfunctioning cylinder does not return to normal A
The malfunctioning cylinder returned to normal B



A

9.INSPECT OTHER RELATED COMPONENTS

B

18.REPAIR OR REPLACE MALFUNCTIONING PARTS
9.INSPECT OTHER RELATED COMPONENTS
a.

Check the power source circuit, wire harness and connectors.


Result:
Proceed to
NEXT



NEXT

18.REPAIR OR REPLACE MALFUNCTIONING PARTS
10.REPLACE FUEL INJECTOR ASSEMBLY
a.

Replace the fuel injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:
·

If the air fuel ratio learned value is corrected to the positive side for all operating ranges due to low fuel injector assembly injection volume, replace the fuel injector assemblies of all cylinders.

·

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

19.CONDUCT CONFIRMATION TEST
11.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure. If the compression pressure of a cylinder is low, inspect the engine assembly and repair or replace parts as necessary.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

18.REPAIR OR REPLACE MALFUNCTIONING PARTS
12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.


b.

According to the display on the GTS, read the Data List when the ignition switch is turned to ON and while maintaining an engine speed of 3000 rpm.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

Result:
Result Proceed to
Idling (without load): 2.5 to 4.7 gm/sec
Engine speed 3000 rpm (without load): 18.3 to 25.8 gm/sec
A
Other than above B



A

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

17.CHECK INTAKE SYSTEM
13.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.


b.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


c.

Idle the engine.


d.

According to the display on the GTS, perform the Active Test and check the vehicle conditions when increasing and decreasing the fuel injection volume.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
50004 372 8 225,512,218,510
NOTICE:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Read the output voltage immediately after warming up the air fuel ratio sensor and heated oxygen sensor to avoid an inaccurate reading due to a sensor cooling.



HINT:

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.


Result:
GTS Display
(Sensor)
Injection Volume Voltage
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
(Air fuel ratio)
12.5% Below 3.1 V
-12.5% Higher than 3.4 V
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
(Heated oxygen)
12.5% Higher than 0.55 V
-12.5% Below 0.4 V



Result:
Result Proceed to
Output voltage values are abnormal A
Malfunction disappears when fuel injection volume is increased B
Malfunction is still present when fuel injection volume is increased, even if output voltage values are normal C



A

14.REPLACE AIR FUEL RATIO SENSOR AND HEATED OXYGEN SENSOR

B

15.REPLACE FUEL INJECTOR ASSEMBLY

C

16.INSPECT OTHER RELATED COMPONENTS
14.REPLACE AIR FUEL RATIO SENSOR AND HEATED OXYGEN SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

19.CONDUCT CONFIRMATION TEST
15.REPLACE FUEL INJECTOR ASSEMBLY
a.

Replace the fuel injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

19.CONDUCT CONFIRMATION TEST
16.INSPECT OTHER RELATED COMPONENTS
a.

Inspect other related components.

HINT:

If the malfunctioning part could not be determined by performing the preceding inspections, one of the following malfunctions is suspected.

·

Engine mount deterioration

·

Deposits in the intake manifold or on an intake valve

·

Delay in fuel supply due to adherence of the fuel to the deposits




Result:
Proceed to
NEXT



NEXT

18.REPAIR OR REPLACE MALFUNCTIONING PARTS
17.CHECK INTAKE SYSTEM
a.

Check for air leaks or blockage in the intake system components. If a connection problem or foreign matter is found, repair the connection or remove the foreign matter.

HINT:
·

If there is foreign matter in the intake system components, remove it before proceeding to the next step.

·

If there is no foreign matter in the intake system components, check for foreign matter in the mass air flow meter sub-assembly. If there is foreign matter in the mass air flow meter sub-assembly, remove it.




Result:
Proceed to
NEXT



NEXT

18.REPAIR OR REPLACE MALFUNCTIONING PARTS
18.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning part.


b.

Perform "Inspection After Repair" after repairing or replacing the malfunctioning part.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

19.CONDUCT CONFIRMATION TEST
19.CONDUCT CONFIRMATION TEST
a.

Check that the idle has returned to normal.


Result:
Proceed to
OK
NG



OK

END

NG

20.REMOVE FOREIGN OBJECT (CLEAN THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)
20.REMOVE FOREIGN OBJECT (CLEAN THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY)
a.

Clean off any deposits from the inside of the throttle with throttle position sensor body assembly.


b.

Push open the throttle valve and wipe off any carbon from the valve and bore using a piece of cloth soaked in non-residue solvent.

A213929C10
1.958,1.323 2.354,1.594 true 1.969,1.146 2.354,1.146 true 0.781,2.479 1.229,2.375 true 1.729,3.625 1.521,3.073 true 1.031,0.573 1.604,0.688 true 0.771,3.073 1.385,2.729 true 0.271,0.344 0.583,0.5 0.313,0.156 10 false *1 0.854,0.51 1.167,0.667 0.313,0.156 10 false *2 2.406,1.542 2.656,1.823 0.25,0.281 10 false *e 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.688,0.177 2,0.333 0.313,0.156 10 false *b 1.688,1.927 2,2.083 0.313,0.156 10 false *c 4.771,0.917 5.083,1.073 0.313,0.156 10 false *d 0.583,2.417 0.896,2.573 0.313,0.156 10 false *2 1.667,3.625 2,3.802 0.333,0.177 10 false *e 0.594,3.031 0.906,3.188 0.313,0.156 10 false *3 2.385,1.083 2.698,1.24 0.313,0.156 10 false *3
*1 Throttle with Throttle Position Sensor Body Assembly *2 Bore
*3 Valve - -
*a Reference *b Throttle with Throttle Position Sensor Body Assembly Cross-section Diagram
*c When valve fully opened *d Do not directly apply cleaner
*e Deposits - -



NOTICE:
·

Make sure that the cloth or your fingers do not get caught in the valve.

·

Make sure that foreign matter does not enter the throttle valve.

·

Do not directly apply non-residue solvent to the throttle with throttle position sensor body assembly or wash the throttle with throttle position sensor body assembly. Cleaning solvent may leak into the motor from the shaft and cause problems such as rust or valve movement problems.

·

If there is coating material on the edge of the valve, be careful not to remove it.



HINT:

The illustrations are for reference only. Actual parts may differ.


Result:
Proceed to
NEXT



NEXT

21.PERFORM CONFIRMATION DRIVING PATTERN
21.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform "Inspection After Repair" after cleaning the throttle body with motor assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Allow the engine to idle for 3 minutes or more and confirm that the engine speed is within the specified range.

HINT:

If the engine is operated without performing learning value reset and idle learning after cleaning the deposits from the throttle body with motor assembly, the idle speed may increase.



Result:
Proceed to
NEXT



NEXT

22.CONDUCT CONFIRMATION TEST
22.CONDUCT CONFIRMATION TEST
a.

Check that the idle has returned to normal.


Result:
Proceed to
NEXT



NEXT

END