To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
28800 3.INSPECT BATTERY
16361A 4.INSPECT FAN AND GENERATOR V BELT
16620 5.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
17801 6.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
Check that the air cleaner filter element sub-assembly is not excessively dirty.
If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.
If cleaning the air cleaner filter element sub-assembly, blow compressed air to clean it.
Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.
When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.
When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.
Reinstall the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
19100P 7.INSPECT SPARK PLUG
8.INSPECT IGNITION TIMING
Turn all electrical systems off.
Perform the inspection when the cooling fan motor is turned off.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1
| Tester Display |
|---|
| Ignition Timing Cylinder #1 |
7 to 24° BTDC at idle
Check the ignition timing with the cooling fans off.
Turn off all the electrical systems and the A/C.
When checking the ignition timing, the transmission should be in park.
Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Ignition Timing Cylinder #1 |
Monitor Ignition Timing Cylinder #1 of the Data List.
8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)
Check that the ignition timing advances immediately when the engine speed is increased.
9.INSPECT ENGINE IDLE SPEED
Turn all the electrical systems off.
Perform the inspection when the cooling fan motor is turned off.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Inspect the engine idle speed.
690 to 790 rpm (transmission in neutral and A/C switch off)
10.INSPECT COMPRESSION
Warm up and stop the engine.
Remove the intake air surge tank.
Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL
Remove the 6 spark plugs.
Disconnect the 6 fuel injector connectors.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole. (Procedure A)
While cranking the engine, measure the compression pressure. (Procedure B)
1400 kPa (14.3 kgf/cm2, 203 psi) or higher
1000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.
Measure the compression in as short a time as possible.
Repeat procedures A and B for each cylinder.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat procedures A and B for cylinders with low compression.
If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 6 injector connectors.
Install the 6 spark plugs.
Click hereGeneral>MAINTENANCE>1GR-FE SPARK PLUG>INSTALLATION
Install the intake air surge tank.
Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSTALLATION
11.INSPECT CO/HC
This check is to determine whether or not the idle CO/HC concentration complies with regulations.
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check the CO/HC concentration during idling and/or at 2500 rpm.
When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.
If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.
Check the air fuel ratio sensor operation.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION
Check the heated oxygen sensor operation.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION
See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.
| CO | HC | Symptom | Causes |
|---|---|---|---|
| Normal | High | Rough idling |
1.
Faulty ignition:
-
Incorrect timing
-
Plugs are contaminated or shorted, or plug gaps are incorrect
2.
Incorrect valve clearance
3.
Leaky intake and exhaust valves
4.
Leaky cylinders |
| Low | High | Rough idling (Fluctuating HC reading) |
1.
Vacuum leaks:
-
Ventilation hoses
-
Intake manifold
-
Throttle body
2.
Lean mixture causing misfire |
| High | High | Rough idling (Black smoke from exhaust) |
1.
Restricted air filter
2.
Plugged PCV valve
3.
Faulty SFI system:
-
Faulty pressure regulator
-
Defective engine coolant temperature sensor
-
Faulty mass air flow meter
-
Faulty ECM
-
Faulty injectors
-
Faulty throttle position sensor |