Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold Bank 1  P043000  Catalyst System Efficiency Below Threshold Bank 2  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P042000 Catalyst System Efficiency Below Threshold Bank 1 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Heated oxygen sensor (bank 1 sensor 2)

·

Exhaust manifold assembly RH (TWC: Front catalyst and Rear catalyst)


Comes on SAE: P0420
P043000 Catalyst System Efficiency Below Threshold Bank 2 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Heated oxygen sensor (bank 2 sensor 2)

·

Exhaust manifold assembly LH (TWC: Front catalyst and Rear catalyst)


Comes on SAE: P0430

CATALYST LOCATION

A486276C01
1.25,2.052 0.917,1.5 0.917,1.5 0.667,1.5 true 2.458,2.927 2.667,2.333 2.667,2.333 2.917,2.333 true 1,1.083 1.25,1.083 1.25,1.083 1.583,1.688 true 0.333,3.083 0.583,3.083 0.583,3.083 0.917,2.5 true 1.75,3.667 1.5,3.667 1.5,3.667 1.219,4.198 true 5.25,3.25 5,3.25 5,3.25 4.833,2.833 true 2.219,3.927 1.969,3.927 1.969,3.927 1.688,4.458 true 0.833,5.667 1.083,5.667 1.083,5.667 1.417,5.083 true 6.417,1.417 6.167,1.417 6.167,1.417 6,1 true 0.5,1.417 0.75,1.583 0.25,0.167 10 false *1 1.802,3.583 2.052,3.75 0.25,0.167 10 false *2 0.833,1 1.146,1.156 0.313,0.156 10 false *3 2.271,3.844 2.583,4 0.313,0.156 10 false *4 0.167,3.01 0.479,3.167 0.313,0.156 10 false *5 0.667,5.583 0.979,5.74 0.313,0.156 10 false *6 3,2.26 3.313,2.417 0.313,0.156 10 false *7 5.333,3.177 5.646,3.333 0.313,0.156 10 false *8 6.5,1.333 6.813,1.531 0.313,0.198 10 false *9
*1 Air Fuel Ratio Sensor (Bank 1 Sensor 1) *2 Air Fuel Ratio Sensor (Bank 2 Sensor 1)
*3 Heated Oxygen Sensor (Bank 1 Sensor 2) *4 Heated Oxygen Sensor (Bank 2 Sensor 2)
*5 Exhaust Manifold Assembly RH
- TWC: Front Catalyst and Rear Catalyst
*6 Exhaust Manifold Assembly LH
- TWC: Front Catalyst and Rear Catalyst
*7 Front Exhaust Pipe Assembly *8 Center Exhaust Pipe Assembly
*9 Tail Exhaust Pipe Assembly - -


CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969E26
1.833,0.333 1.667,0.333 1.667,0.333 1.302,0.865 false 0.771,1.156 1.5,1.313 0.729,0.156 10 60 km/h 0.917,2.167 1.333,2.427 0.417,0.26 10 Idling 0.167,2.5 1.333,2.75 1.167,0.25 10 Ignition Switch off 1.417,2.729 2.271,3 0.854,0.271 10 Warming up 2.365,2.75 3.083,3.083 0.719,0.333 10 10 minutes or more 4.156,2.729 4.917,3.083 0.76,0.354 10 10 minutes or more 1.917,0.25 3.469,0.427 1.552,0.177 10 Between 75 to 100 km/h 1.667,2.083 1.896,2.26 0.229,0.177 10 [A] 2.594,1 2.917,1.177 0.323,0.177 10 [B]* 3.156,3.156 3.385,3.333 0.229,0.177 10 [C] 6.76,3.167 6.99,3.344 0.229,0.177 10 [H] 3.458,2.083 3.667,2.26 0.208,0.177 10 [D] 6.146,0.583 6.5,0.76 0.354,0.177 10 [G]* 4.333,0.99 4.698,1.167 0.365,0.177 10 [E]* 5.01,3.156 5.208,3.333 0.198,0.177 10 [F] 3.396,2.729 4,3.083 0.604,0.354 10 Warming up 5.917,2.75 6.729,3.135 0.813,0.385 10 10 minutes or more 0.083,3.354 4.583,3.583 4.5,0.229 10 *: Drive the vehicle while keeping the engine load as constant as possible

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the GTS on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P042000 or P043000.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.



18.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


19.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



21.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

22.

Input the DTC: P042000 or P043000.

23.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A292989E04
4.875,3.094 4.875,3.344 false 5.177,3.094 5.177,3.344 false 4.875,3.344 5.458,3.344 false 0.583,0.688 1.51,0.927 0.927,0.24 10 Engine Speed 0.865,1.031 1.479,1.26 0.615,0.229 10 3000 rpm 0.865,1.573 1.542,1.771 0.677,0.198 10 2000 rpm 1.104,2.542 1.594,2.802 0.49,0.26 10 Idling 0.365,2.802 1.521,3 1.156,0.198 10 Ignition Switch off 2.104,3.167 2.958,3.396 0.854,0.229 10 Warming up 3.333,3.167 4.531,3.385 1.198,0.219 10 At least 3 minutes 5.5,3.26 6.198,3.51 0.698,0.25 10 2 seconds 4.865,3.396 5.333,3.583 0.469,0.188 10 Check 6.615,2.76 6.958,3 0.344,0.24 10 Time 1.646,2.656 1.885,2.896 0.24,0.24 10 (a) 2.094,2.417 2.354,2.677 0.26,0.26 10 (b) 3.625,0.865 3.854,1.094 0.229,0.229 10 (c) 4.802,0.875 5.052,1.156 0.25,0.281 10 (d) 5.104,1.458 5.323,1.729 0.219,0.271 10 (d)

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS.


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A201081E21
0.104,0.135 4.417,0.375 4.313,0.24 10 false Voltage Output When Active Air Fuel Ratio Control Not Performed: 2.719,0.74 3.76,0.948 1.042,0.208 10 false Normal Catalyst 5.083,0.74 6.573,0.969 1.49,0.229 10 false Deteriorated Catalyst 2.833,3.26 3.646,3.448 0.813,0.188 10 false 10 seconds 5.406,3.271 6.198,3.5 0.792,0.229 10 false 10 seconds 1.667,1.083 2.042,1.24 0.375,0.156 10 false 3.4 V 1.667,1.427 2.042,1.604 0.375,0.177 10 false 3.1 V 1.667,2.365 2.042,2.542 0.375,0.177 10 false 1.0 V 1.76,3.052 2.031,3.229 0.271,0.177 10 false 0 V 0.135,1.25 1.5,1.958 1.365,0.708 10 false Waveform of Air Fuel Ratio Sensor in Front of Three-Way Catalytic Converter 0.177,2.49 1.448,3.229 1.271,0.74 10 false Waveform of Heated Oxygen Sensor Behind Three-Way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P042000 or P043000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 and P017400 (System Too Lean), and P017200 and P017500 (System Too Rich).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000 AND/OR P043000)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P042000 and/or P043000 are output A
DTC P042000 and/or P043000 and other DTCs are output B


HINT:

If any DTCs other than P042000 and/or P043000 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Start the engine and warm it up.


b.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


c.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
50004 372 8 225,512,218,510

d.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 Status O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor Active Test, A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 is consistently below 3.1 V, and O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.


HINT:

Refer to "Data List / Active test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Voltage B2S1, O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

3.CHECK FOR EXHAUST GAS LEAK

B

4.REPLACE AIR FUEL RATIO SENSOR

C

5.CHECK FOR EXHAUST GAS LEAK

D

7.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

11.CHECK DTC OUTPUT (DTC P042000 AND/OR P043000)

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

6.REPLACE HEATED OXYGEN SENSOR

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
6.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
8.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100, P017200, P017400 or P017500 Inspection Procedure.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P017100


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P042000 and/or P043000 is output A
DTCs are not output B




A

11.CHECK DTC OUTPUT (DTC P042000 AND/OR P043000)

B

END

11.CHECK DTC OUTPUT (DTC P042000 AND/OR P043000)
HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P042000 is output A
DTC P043000 is output B
DTC P042000 and P043000 are output C




A

REPLACE EXHAUST MANIFOLD ASSEMBLY RH (FRONT CATALYST AND REAR CATALYST)

B

REPLACE EXHAUST MANIFOLD ASSEMBLY LH (FRONT CATALYST AND REAR CATALYST)

C

12.REPLACE EXHAUST MANIFOLD ASSEMBLY RH (FRONT CATALYST AND REAR CATALYST)
12.REPLACE EXHAUST MANIFOLD ASSEMBLY RH (FRONT CATALYST AND REAR CATALYST)
a.

Replace the exhaust manifold assembly RH.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE EXHAUST MANIFOLD ASSEMBLY LH (FRONT CATALYST AND REAR CATALYST)