Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P017100  System Too Lean Bank 1  P017200  System Too Rich Bank 1  P017400  System Too Lean Bank 2  P017500  System Too Rich Bank 2  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P017100 System Too Lean Bank 1 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

PCV valve and hose

·

PCV hose connections

·

Wire harness or connector

·

ECM


Comes on SAE: P0171
P017200 System Too Rich Bank 1 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Wire harness or connector

·

ECM


Comes on SAE: P0172
P017400 System Too Lean Bank 2 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

PCV valve and hose

·

PCV hose connections

·

Wire harness or connector

·

ECM


Comes on SAE: P0174
P017500 System Too Rich Bank 2 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Wire harness or connector

·

ECM


Comes on SAE: P0175

HINT:
·

When DTC P017100 or P017400 is stored, the actual air fuel ratio is on the lean side. When DTC P017200 or P017500 is stored, the actual air fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 or P017400 may be stored. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.



MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

The average fuel trim learned value is +48% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.

A277870E02
3.792,1.635 3.427,1.635 false 3.792,3.094 3.438,3.094 false 2.667,1.635 2.99,1.635 false 2.667,3.083 2.99,3.083 false 2.635,0.531 4.365,0.729 1.729,0.198 10 false Fuel Compensatio Amount 0.063,1.344 0.5,1.542 0.438,0.198 10 false +48%: 0.063,1.542 2.604,1.75 2.542,0.208 10 false Malfunction Threshold of Lean Condition 0.063,2.99 2.583,3.177 2.521,0.188 10 false Malfunction Threshold of Rich Condition 0.063,2.771 0.469,2.99 0.406,0.219 10 false -35%: 3.021,1.552 3.323,1.708 0.302,0.156 10 false 1.48 3.073,2.427 3.313,2.625 0.24,0.198 10 false 1.0 3.021,3 3.344,3.198 0.323,0.198 10 false 0.65 0.063,1.146 1.354,1.333 1.292,0.188 10 false P017100, P017400 0.063,2.583 1.313,2.76 1.25,0.177 10 false P017200, P017500

CONFIRMATION DRIVING PATTERN

A288929E43
2.771,2.083 3.083,0.281 3.083,0.281 3.333,0.281 false 0.573,0.042 1.625,0.292 1.052,0.25 10 false Vehicle Speed 1.083,0.365 1.698,0.563 0.615,0.198 10 false 100 km/h 1.146,1.229 1.76,1.427 0.615,0.198 10 false 60 km/h 1.333,1.979 1.948,2.177 0.615,0.198 10 false Idling 0.521,2.49 1.708,2.781 1.188,0.292 10 false Ignition Switch ON 2.031,2.344 2.646,2.542 0.615,0.198 10 false [A] 3.385,0.198 6.344,0.448 2.958,0.25 10 false Engine coolant temperatures is 75°C or higher 3.281,1.865 3.896,2.063 0.615,0.198 10 false [C] 2.521,1.865 3.135,2.063 0.615,0.198 10 false [B] 4.865,0.479 5.479,0.677 0.615,0.198 10 false [D] 2.115,3.083 3.344,3.26 1.229,0.177 10 false Warming up 3.073,3.083 3.719,3.542 0.646,0.458 10 false 2 minutes or more 5.604,3.365 6.573,3.552 0.969,0.188 10 false [E] 4.323,3.094 5.552,3.271 1.229,0.177 10 false 5 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:

If a pending DTC is output, the system is malfunctioning.



WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P219519 for the air fuel ratio sensor circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P219519

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P017100, P017200, P017400 OR P017500)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P017100, P017200, P017400 or P017500 is output A
DTC P017100, P017200, P017400 or P017500 and other DTCs are output B


HINT:

If any DTCs other than P017100, P017200, P017400 or P017500 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

PCV valve and hose are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.


HINT:
·

If a malfunction is detected while the brake pedal is being depressed, vacuum leaks in the brake booster assembly are suspected. Inspect the brake booster assembly.

·

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Start the engine.


b.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


c.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
50004 372 8 225,512,218,510

d.

Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 Status O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector assembly blockage

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


Rich Rich Actual air fuel ratio rich
·

Fuel injector assembly leak or blockage

·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor




Lean: During Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor Active Test, A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 is consistently below 3.1 V, and O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and the heated oxygen sensor alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Voltage B2S1, O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

5.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Turn the ignition switch to ON.


b.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MAF)

NG

6.READ VALUE USING GTS (MAF)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

c.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Shift lever position: N
A/C: Off
Engine Speed: 3000 rpm
Between 18.3 gm/sec and 25.8 gm/sec



Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE

NG

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
7.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 (to Misfire Count Cylinder #6).

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 (to Misfire Count Cylinder #6).

·

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400 OR P017500)

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

21.INSPECT A/F RELAY
13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C87,C92,C88)Location & Routing

Click Connector(C87)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C88)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

C87-1 (HA1A) - C92-22 (HA1A) Always Below 1 Ω
C87-3 (A1A+) - C92-98 (A1A+) Always Below 1 Ω
C87-4 (A1A-) - C92-97 (A1A-) Always Below 1 Ω
C88-1 (HA2A) - C92-45 (HA2A) Always Below 1 Ω
C88-3 (A2A+) - C92-121 (A2A+) Always Below 1 Ω
C88-4 (A2A-) - C92-120 (A2A-) Always Below 1 Ω
C87-1 (HA1A) or C92-22 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C87-3 (A1A+) or C92-98 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C87-4 (A1A-) or C92-97 (A1A-) - Body ground and other terminals Always 10 kΩ or higher
C88-1 (HA2A) or C92-45 (HA2A) - Body ground and other terminals Always 10 kΩ or higher
C88-3 (A2A+) or C92-121 (A2A+) - Body ground and other terminals Always 10 kΩ or higher
C88-4 (A2A-) or C92-120 (A2A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400 OR P017500)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400 OR P017500)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P017100, P017200, P017400 or P017500 is output A
DTCs are not output B




A

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

B

END

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400 OR P017500)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P017400 OR P017500)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P017100, P017200, P017400 or P017500 is output A
DTCs are not output B




A

18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

19.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P017100, P017200, P017400 or P017500 is output B




A

END

B

21.INSPECT A/F RELAY

Result:
Proceed to
OK
NG



OK

22.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)

NG

REPLACE A/F RELAY

22.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)
a.
A485543C03
0.24,0.177 0.552,0.375 0.313,0.198 10 false *1 2.281,2.438 2.594,2.635 0.313,0.198 10 false *a
*1 Engine Room Relay Block No. 2
*a A/F Relay Terminal


Remove the A/F relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (A/F relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, EFI MAIN NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F RELAY - BATTERY)

23.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, EFI MAIN NO.1 RELAY)
a.

Remove the A/F relay.


b.

Remove the EFI MAIN NO.1 relay.


c.

Disconnect the air fuel ratio sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C87,C88)Location & Routing

Click Connector(C87)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C88)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

3 (A/F relay) - C87-2 (+B) Always Below 1 Ω
3 (A/F relay) - C88-2 (+B) Always Below 1 Ω
2 (A/F relay) - 3 (EFI MAIN NO.1 relay) Always Below 1 Ω
1 (A/F relay) - Body ground Always Below 1 Ω
3 (A/F relay) or C87-2 (+B) - Body ground Always 10 kΩ or higher
3 (A/F relay) or C88-2 (+B) - Body ground Always 10 kΩ or higher
2 (A/F relay) or 3 (EFI MAIN NO.1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR