Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM38G0E _59 Vehicle Exterior _100456 WIPER / WASHER _0467584 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the washer fluid level is lower than a certain level, a warning message is displayed on the combination meter assembly.

WIRING DIAGRAM

E463862E05
4.073,3.594 5.729,3.969 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.146,3.042 3.458,3.24 0.313,0.198 10 false IC 3.281,4.563 5.427,4.833 2.146,0.271 10 false Power Distribution Box Assembly 0.635,6.406 2.375,6.615 1.74,0.208 10 false : CAN Communication Line 0.646,6 2.375,6.229 1.729,0.229 10 false : CXPI Communication Line 4.906,1.719 6.927,1.99 2.021,0.271 10 false Level Warning Switch Assembly 3.135,1.74 4.771,1.958 1.635,0.219 10 false Washer Wiring Assembly 4.677,0.75 5.021,0.958 0.344,0.208 10 false B51 4.677,1.25 5.01,1.51 0.333,0.26 10 false B51 4.74,0.542 4.896,0.74 0.156,0.198 10 false 1 4.75,1.031 4.906,1.229 0.156,0.198 10 false 2 1.167,0.719 1.635,0.927 0.469,0.208 10 false WLVL 1.677,0.635 1.99,0.833 0.313,0.198 10 false 12 2.781,0.75 3.115,0.948 0.333,0.198 10 false BB1 2.854,0.542 3.01,0.74 0.156,0.198 10 false 1 5.063,0.646 5.219,0.844 0.156,0.198 10 false S 5.063,1.115 5.219,1.313 0.156,0.198 10 false E 2.781,1.25 3.083,1.458 0.302,0.208 10 false BB1 0.333,3.76 1.708,4.135 1.375,0.375 10 false Semiconductor Power Integration ECU 0.354,3.594 0.813,3.792 0.458,0.198 10 false B57 4.031,5.969 5.927,6.219 1.896,0.25 10 false Combination Meter Assembly 2.865,1.042 3.021,1.24 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

The wiper and washer system uses the CAN and CXPI communication system. First, confirm that there is no malfunction in the CAN and CXPI communication system.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Washer Level Switch Status Washer fluid level warning switch status Washer Level Switch ON, Washer Level Switch OFF or Unknown Washer Level Switch ON: Washer fluid level not low
Washer Level Switch OFF: Washer fluid level low
Unknown: Washer fluid level not detected
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Washer Level Switch Status
50003 473 436
OK:

The GTS display changes correctly in response to the washer fluid level warning switch status.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT LEVEL WARNING SWITCH ASSEMBLY
2.INSPECT LEVEL WARNING SWITCH ASSEMBLY

OK

3.INSPECT WASHER WIRING ASSEMBLY

NG

REPLACE LEVEL WARNING SWITCH ASSEMBLY

3.INSPECT WASHER WIRING ASSEMBLY
a.

Remove the washer wiring assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B51,BB1)Location & Routing

Click Connector(B51)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Level Warning Switch Assembly

Click Connector(BB1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Engine Room Main Wire and Washer Wiring Assembly

B51-1 (S) - BB1-1 Always Below 1 Ω
B51-2 (E) - BB1-2 Always Below 1 Ω
B51-1 (S) or BB1-1 - Body ground Always 10 kΩ or higher
B51-2 (E) or BB1-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - SEMICONDUCTOR POWER INTEGRATION ECU)

NG

REPLACE WASHER WIRING ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - SEMICONDUCTOR POWER INTEGRATION ECU)
a.

Disconnect the BB1 washer wiring assembly connector.


b.

Disconnect the B57 semiconductor power integration ECU connector.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (LEVEL WARNING SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the B51 level warning switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B51)Location & Routing

Click Connector(B51)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Level Warning Switch Assembly

B51-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR