| Even when the wireless charging system is turned on, the indicator light (green) does not illuminate |
Wireless charger power source circuit |
 |
| Mobile wireless charger cradle assembly |
 |
| When the wireless charging system is turned on, the indicator (green) illuminates, but the indicator (amber) does not illuminate when a rechargeable device is placed on the charging area (wireless charging does not start) |
Check that the device being used is a Qi-compatible rechargeable device |
- |
| Remove any cases and accessories |
- |
| Check that a flat object or a gap with a thickness of 2.0 mm (0.079 in.) or more is not present between the compatible device (without a cover or any accessories attached) and the charging area |
- |
| Check that a flat object or small item with a thickness of 2.0 mm (0.079 in.) or more is not placed between the compatible device and the charging area |
- |
| Check that the rechargeable device is not fully charged |
- |
| Check that the compatible device is placed in the charging area on the charging tray |
 |
| Check that the rechargeable device is placed on the charging area with its charging surface facing down |
- |
| Check that the vehicle is not in an environment where it may be affected by strong radio waves or electrical noise |
- |
| Check that there is not more than 1 compatible device placed on the charging tray |
- |
| Check that a charging cable is not connected to the rechargeable device |
- |
| Check that the temperature of the compatible device is within the charging temperature range of the device |
- |
| Check if wireless charging of the rechargeable device is possible using another Qi-compatible wireless charging system |
- |
| Check operation using a compatible device other than the device that is reported to be malfunctioning |
- |
| Status signal circuit |
 |
| Mobile wireless charger cradle assembly |
 |
| The indicator does not illuminate alternately green/amber even if the charging method is switched to fast charging while charging.(fast charging does not start) |
Check that the device being used is a Qi-compatible (fast charging) rechargeable device. |
- |
| Operate the mobile wireless charger switch and check that the wireless charging system can be turned off. |
- |
| Use another Qi-compatible device to check that it also switches to fast charging*2 |
- |
| Mobile wireless charger cradle assembly |
 |
| When the wireless charging system is turned on, the indicator (green) illuminates and when a rechargeable device is placed on the charging area, the indicator (amber) illuminates, but the indicator (green) illuminates again before wireless charging is completed (wireless charging does not complete) |
Check that the compatible device is placed in the charging area on the charging tray |
 |
| Check that temperature of the rechargeable device is not excessively high or low |
- |
| Check that the vehicle is not in an environment where it may be affected by strong radio waves or electrical noise |
- |
| Status signal circuit |
 |
| Mobile wireless charger cradle assembly |
 |
| When the taillight is on, the indicator light of the mobile wireless charger switch does not illuminate |
Wireless charger illumination circuit |
 |
| Mobile wireless charger cradle assembly |
 |
| The indicator light (amber) blinks (pattern 1)* |
Status signal circuit |
 |
| Mobile wireless charger cradle assembly |
 |
| The indicator light (amber) blinks (pattern 2)* |
Check if the charging frequency is being changed |
 |
| Mobile wireless charger cradle assembly |
 |
| The indicator light (amber) blinks (pattern 3)* |
Check that the device being used is a Qi-compatible rechargeable device |
- |
| Remove any cases and accessories |
- |
| Check that a flat object or a gap with a thickness of 2.0 mm (0.079 in.) or more is not present between the compatible device (without a cover or any accessories attached) and the charging area |
- |
| Check that a flat object or small item with a thickness of 2.0 mm (0.079 in.) or more is not placed between the compatible device and the charging area |
- |
| Check that the compatible device is placed in the charging area on the charging tray |
 |
| Check that the rechargeable device is in the same position as when charging was started |
- |
| Mobile wireless charger cradle assembly |
 |
| The indicator light (amber) blinks (pattern 4)* |
Check that temperature of the mobile wireless charger cradle assembly is not excessively high |
- |
| Check that the indicator does not blink in amber (pattern 4) after removing the compatible device from the mobile wireless charger cradle assembly and cooling it to room temperature |
- |
| Mobile wireless charger cradle assembly |
 |