Home › Vehicle Interior › METER / GAUGE / DISPLAY › HEADUP DISPLAY SYSTEM
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0469279 HEADUP DISPLAY SYSTEM C

METER / GAUGE / DISPLAY  HEADUP DISPLAY SYSTEM  B132187  Lost Communication with EMV Missing Message  


DESCRIPTION

*1: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)

*2: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) or w/ Navigation System


The meter mirror sub-assembly receives signals from the radio and display receiver assembly*1 or radio receiver assembly*2 via local bus communication and displays audio and system and navigation system information on the headup display.

This DTC is stored when the meter mirror sub-assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B132187 Lost Communication with EMV Missing Message
·

DTC Detection Condition: IG+ voltage 9.5 to 11.5 V or higher

·

Malfunction Status: Lost communication with radio and display receiver assembly*1

·

Malfunction Status: Lost communication with radio receiver assembly*2

·

Malfunction Duration: 30 seconds or more


·

Harness or connector

·

Meter mirror sub-assembly

·

Radio and display receiver assembly*1

·

Radio receiver assembly*2


DTC stored Head Up Display A

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display):
Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Meter Mirror Sub-assembly (Head Up Display) Radio and Display Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187 Local bus (Open or short)
Meter mirror sub-assembly (Internal malfunction)
Combination meter assembly (Internal malfunction)
Radio and display receiver assembly (Internal malfunction)
Pattern 2 B132187 - B1325 - Local bus (Open)
Meter mirror sub-assembly (Internal malfunction)
Pattern 3 B132187 - - B132187 Radio and display receiver assembly (Internal malfunction)
Pattern 4 B132187 - - - Meter mirror sub-assembly (Internal malfunction)

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) or w/ Navigation System:
Pattern DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Meter Mirror Sub-assembly (Head Up Display) Radio Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187 Local bus (Open or short)
Meter mirror sub-assembly (Internal malfunction)
Combination meter assembly (Internal malfunction)
Radio receiver assembly (Internal malfunction)
Pattern 2 B132187 - B1325 - Local bus (Open)
Meter mirror sub-assembly (Internal malfunction)
Pattern 3 B132187 - - B132187 Radio receiver assembly (Internal malfunction)
Pattern 4 B132187 - - - Meter mirror sub-assembly (Internal malfunction)

WIRING DIAGRAM

E461155E03
0.719,1.594 1.635,1.781 0.917,0.188 10 false I13*1, I12*2 0.719,1.781 3.188,2 2.469,0.219 10 false Radio and Display Receiver Assembly*1 0.719,2.042 2.479,2.25 1.76,0.208 10 false Radio Receiver Assembly*2 1.719,0.542 2.146,0.708 0.427,0.167 10 false CNH1 1.729,1.073 2.156,1.24 0.427,0.167 10 false CNL1 2.198,0.375 2.365,0.542 0.167,0.167 10 false 5 2.198,0.927 2.365,1.104 0.167,0.177 10 false 6 5.104,0.521 5.406,0.719 0.302,0.198 10 false TX+ 5.115,1.083 5.417,1.281 0.302,0.198 10 false TX- 4.833,0.385 5.031,0.563 0.198,0.177 10 false 14 4.833,0.938 5.031,1.115 0.198,0.177 10 false 15 4.938,1.583 5.177,1.781 0.24,0.198 10 false I17 4.927,1.76 6.667,1.979 1.74,0.219 10 false Meter Mirror Sub-assembly 1.125,3.906 1.313,4.094 0.188,0.188 10 false I5 1.667,2.854 2.125,3.031 0.458,0.177 10 false MSCH 1.677,3.417 2.177,3.604 0.5,0.188 10 false MSCL 2.167,2.688 2.365,2.865 0.198,0.177 10 false 14 2.188,3.26 2.385,3.438 0.198,0.177 10 false 30 1.104,4.073 3.021,4.313 1.917,0.24 10 false Combination Meter Assembly 0.844,4.448 2.875,4.646 2.031,0.198 10 false : Local Bus Communication Line 0.208,5.031 5.542,5.271 5.333,0.24 10 false *1: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display) 0.219,5.344 6.969,5.552 6.75,0.208 10 false *2: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) or w/ Navigation System

CAUTION / NOTICE / HINT

NOTICE:
·

To measure the resistance of the CAN bus, turn the ignition switch off, wait at least 1 minutes without operating any keys or switches or opening or closing the doors, disconnect the battery, wait at least 1 minutes again, and then measure the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

When checking each connector, press the connector case in the direction of the connection before disconnecting the connectors, and check that there are no disconnections or looseness.

·

When disconnecting the connectors, check that there is no damage, deformation, or corrosion of the connector terminals and connector case.

·

Depending on the parts that are replaced, performing initialization, registration or calibration may be needed.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display) A
w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) or w/ Navigation System B



A

2.CHECK FOR DTC

B

4.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check each system for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Body Electrical > Combination Meter > Trouble Codes
50001 409
Body Electrical > Head Up Display > Trouble Codes
50001 408

Pattern DTC Output Part Name
(Display on GTS)
Meter Mirror Sub-assembly (Head Up Display) Radio and Display Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187
Pattern 2 B132187 - B1325 -
Pattern 3 B132187 - - B132187
Pattern 4 B132187 - - -

Result:
Result Proceed to
Pattern 1 is output A
Pattern 2 is output B
Pattern 3 is output C
Pattern 4 is output D



A

GO TO METER / GAUGE SYSTEM (B132187)

B

3.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

C

D

REPLACE METER MIRROR SUB-ASSEMBLY

3.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN WIRE OR CONNECTOR

4.CHECK FOR DTC
a.

Check each system for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Body Electrical > Combination Meter > Trouble Codes
50001 409
Body Electrical > Head Up Display > Trouble Codes
50001 408

Pattern DTC Output Part Name
(Display on GTS)
Meter Mirror Sub-assembly (Head Up Display) Radio Receiver Assembly (Navigation System) Combination Meter Assembly (Combination Meter)
Pattern 1 B132187 B1324 B1325 B132187
Pattern 2 B132187 - B1325 -
Pattern 3 B132187 - - B132187
Pattern 4 B132187 - - -

Result:
Result Proceed to
Pattern 1 is output A
Pattern 2 is output B
Pattern 3 is output C
Pattern 4 is output D



A

GO TO METER / GAUGE SYSTEM (B132187)

B

5.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

C

D

REPLACE METER MIRROR SUB-ASSEMBLY

5.CHECK CAN WIRE (METER MIRROR SUB-ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I17 meter mirror sub-assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I17)Location & Routing

Click Connector(I17)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Meter Mirror Sub-Assembly

I17-14 (TX+) - I17-15 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN WIRE OR CONNECTOR