Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM38G0E _54 Brake _100998 PARKING BRAKE _0469398 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060B11  Left Electric Parking Brake Actuator Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060B11 Left Electric Parking Brake Actuator Control Circuit Short to Ground
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to GND).

·

Detection Time:

Approximately 1 second (depending on each malfunction)


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness or connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C458647E01
1.333,0.667 1.927,0.875 0.594,0.208 10 false MRL+ 1.344,1.281 1.958,1.479 0.615,0.198 10 false MRL- 3.615,1.302 4.073,1.5 0.458,0.198 10 false Vt1 3.625,0.698 4.083,0.896 0.458,0.198 10 false Vt1 5.031,1.094 5.208,1.365 0.177,0.271 10 false 1 3.677,1.083 3.854,1.354 0.177,0.271 10 false 5 3.677,0.5 3.854,0.771 0.177,0.271 10 false 2 5.042,0.51 5.219,0.781 0.177,0.271 10 false 2 5.042,1.302 5.354,1.5 0.313,0.198 10 false t2 5.042,0.698 5.354,0.896 0.313,0.198 10 false t2 5.281,1.802 6.75,2.198 1.469,0.396 10 false Parking Brake Actuator Assembly LH 3.708,1.802 4.979,2.354 1.271,0.552 10 false No. 2 Parking Brake Wire Assembly 0.583,1.833 1,2.083 0.417,0.25 10 false B20 0.583,2 2.271,2.656 1.688,0.656 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.813,0.583 2.125,0.781 0.313,0.198 10 false 3 1.813,1.177 2.125,1.375 0.313,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the Vt1 and t2 No. 2 parking brake wire assembly connectors.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Vt1,t2)Location & Routing

Click Connector(Vt1)Body>Differential Wire / Frame Wire>Frame Wire and No. 2 Parking Brake Wire Assembly

Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

Vt1-2 or t2-2 - Body ground and other terminals Always 10 kΩ or higher
Vt1-5 or t2-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)
a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the t2 parking brake actuator assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,t2)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(t2)Body>No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

B20-3 (MRL+) or t2-2 - Body ground Always 10 kΩ or higher
B20-2 (MRL-) or t2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH