Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM
RM38G0E _54 Brake _100998 PARKING BRAKE _0469398 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C061014  Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C061014 Right Electric Parking Brake Actuator Control Circuit Short to Ground or Open
·

Diagnosis Condition:

Ignition switch ON

·

Malfunction Status:

When the ECU power supply is normal, a malfunction in the electric parking brake actuator RH internal circuit is detected.

·

Detection Time:

Approximately 1 second


·

Parking brake actuator assembly RH

·

No. 1 parking brake wire assembly

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

CAUTION / NOTICE / HINT

NOTICE:
·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the Vs1 and s2 No. 1 parking brake wire assembly connectors.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Vs1,s2)Location & Routing

Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assembly

Click Connector(s2)Body>No. 1 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

Vs1-2 - s2-2 Always Below 1 Ω
Vs1-2 or s2-2 - Body ground and other terminals Always 10 kΩ or higher
Vs1-5 - s2-1 Always Below 1 Ω
Vs1-5 or s2-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)
a.

Make sure the No. 1 parking brake wire assembly is securely installed.


b.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the s2 parking brake actuator assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,s2)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(s2)Body>No. 1 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

B20-13 (MRR+) - s2-2 Always Below 1 Ω
B20-13 (MRR+) or s2-2 - Body ground Always 10 kΩ or higher
B20-12 (MRR-) - s2-1 Always Below 1 Ω
B20-12 (MRR-) or s2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH