Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  C123A17  Supply Voltage Circuit Circuit Voltage Above Threshold  


DESCRIPTION

The power steering ECU with motor assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C123A17 Supply Voltage Circuit Circuit Voltage Above Threshold IG voltage is more than 18.5 V
·

EPS-IGR fuse

·

IG power source circuit*1

·

Backup boost converter circuit*2

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly

*1: w/o Stop and Start System

*2: w/ Stop and Start System


WIRING DIAGRAM

C427424E05
5.5,3.125 7.083,3.521 1.583,0.396 10 false Power Steering ECU with Motor Assembly 3.646,1.167 4.375,1.396 0.729,0.229 10 false EPS-IGR 5.323,1 5.76,1.302 0.438,0.302 10 false I71 5.323,2.177 5.677,2.396 0.354,0.219 10 false I70 5.344,0.792 5.781,1.094 0.438,0.302 10 false 1 5.667,1 6.104,1.302 0.438,0.302 10 false IG 5.667,2.188 6.104,2.49 0.438,0.302 10 false PGND 5.365,1.979 5.802,2.281 0.438,0.302 10 false 2 1.521,0.313 3.729,0.5 2.208,0.188 10 false from Engine Stop and Start ECU*1 4.417,0.198 4.646,0.396 0.229,0.198 10 false *1 4.417,0.896 4.646,1.094 0.229,0.198 10 false *2 1.271,0.99 2.896,1.24 1.625,0.25 10 false from IGR-NO. 2 Relay*2 1.427,3.01 3.5,3.26 2.073,0.25 10 false *1: w/ Stop and Start System 1.438,3.344 3.51,3.594 2.073,0.25 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When the power steering ECU with motor assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)

B

4.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)
a.

Disconnect the I71 power steering ECU with motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I71)Location & Routing

Click Connector(I71)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I71-1 (IG) - Body ground Ignition switch ON 8 to 16 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PGND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PGND TERMINAL)
a.

Disconnect the I70 power steering ECU with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I70)Location & Routing

Click Connector(I70)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I70-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE)
a.

Disconnect the I71 power steering ECU with motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I71)Location & Routing

Click Connector(I71)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I71-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PGND TERMINAL)

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (PGND TERMINAL)
a.

Disconnect the I70 power steering ECU with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I70)Location & Routing

Click Connector(I70)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Power Steering ECU Assembly

I70-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR