Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  C18A262  Power Steering "B" Torque Sensor "A" Signal Compare Failure  C18A287  Power Steering "B" Torque Sensor "A" Missing Message  C18A362  Power Steering "B" Torque Sensor "B" Signal Compare Failure  C18A387  Power Steering "B" Torque Sensor "B" Missing Message  


DESCRIPTION

The power steering ECU with motor assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C18A262, C18A287, C18A362 or C18A387 is detected, power assist is stopped or assist amount is limited due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C18A262 Power Steering "B" Torque Sensor "A" Signal Compare Failure Diagnosis Condition: Ignition switch ON
Malfunction Status:
·

The difference between 1A and 1B of the TRQ1 output signal is more than a certain value.

·

TRQ1 output signal 1A or 1B is more than the standard value.

·

TRQ1 output signal 1A or 1B is less than the standard value.


·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18A287 Power Steering "B" Torque Sensor "A" Missing Message Diagnosis Condition: Ignition switch ON
Malfunction Status: When the battery voltage is 9.0 V or more, the TRQ1 signal is not detected, breaks communication protocol, has a CRC error, or has an invalid rolling counter.
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18A362 Power Steering "B" Torque Sensor "B" Signal Compare Failure Diagnosis Condition: Ignition switch ON
Malfunction Status:
·

The difference between 2A and 2B of the TRQ2 output signal is more than a certain value.

·

TRQ2 output signal 2A or 2B is more than the standard value.

·

TRQ2 output signal 2A or 2B is less than the standard value.


·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly
C18A387 Power Steering "B" Torque Sensor "B" Missing Message Diagnosis Condition: Ignition switch ON
Malfunction Status: When the battery voltage is 9.0 V or more, the TRQ2 signal is not detected, breaks communication protocol, has a CRC error, or has an invalid rolling counter.
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly

C18A262 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the ignition switch is ON ○ ○ ○
Malfunction Status The difference between 1A and 1B of the TRQ1 output signal is more than a certain value ○ - -
TRQ1 output signal 1A or 1B is more than the standard value - ○ -
TRQ1 output signal 1A or 1B is less than the standard value - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C18A287 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition When the ignition switch is ON ○ ○ ○ ○
Battery voltage is 9.0 V or more ○ ○ ○ ○
Malfunction Status TRQ1 breaks communication ○ - - -
TRQ1 communication protocol malfunction - ○ - -
TRQ1 CRC error - - ○ -
TRQ1 invalid rolling counter - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C18A362 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the ignition switch is ON ○ ○ ○
Malfunction Status The difference between 1A and 1B of the TRQ1 output signal is more than a certain value ○ - -
TRQ2 output signal 2A or 2B is more than the standard value - ○ -
TRQ2 output signal 2A or 2B is less than the standard value - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C18A387 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition When the ignition switch is ON ○ ○ ○ ○
Battery voltage is 9.0 V or more ○ ○ ○ ○
Malfunction Status TRQ2 breaks communication ○ - - -
TRQ2 communication protocol malfunction - ○ - -
TRQ2 CRC error - - ○ -
TRQ2 invalid rolling counter - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

When the electric power steering column sub-assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION

·

When the power steering ECU with motor assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION



PROCEDURE

1.REPLACE POWER STEERING ECU WITH MOTOR ASSEMBLY AND ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY


Result:
Proceed to
NEXT



NEXT

END