Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  C18A917  Power Steering "B" Torque Sensor "B" Supply Voltage Circuit Voltage Above Threshold  


DESCRIPTION

The power steering ECU with motor assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C18A917 is detected, power assist is stopped or assist amount is limited due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C18A917 Power Steering "B" Torque Sensor "B" Supply Voltage Circuit Voltage Above Threshold TRQV2 voltage is 5.6 V or more
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU with motor assembly


Output ECU: Power steering ECU with motor assembly

WIRING DIAGRAM

C409221E39
0.146,2.979 2.615,3.375 2.469,0.396 10 false Torque Sensor (Electric Power Steering Column Sub-assembly) 5.052,3.177 6.615,3.552 1.563,0.375 10 false Power Steering ECU with Motor Assembly 5.052,2.969 5.344,3.156 0.292,0.188 10 false z17 5.094,1.094 5.865,1.292 0.771,0.198 10 false TRQV2 5.094,1.729 5.865,1.927 0.771,0.198 10 false TRQG2 4.875,1.094 5.031,1.292 0.156,0.198 10 false 3 4.875,1.729 5.031,1.927 0.156,0.198 10 false 2 6.031,0.646 6.344,0.844 0.313,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When the electric power steering column sub-assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION

·

When the power steering ECU with motor assembly has been replaced, perform Steering Actuator ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>CALIBRATION



PROCEDURE

1.INSPECT TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY) (CHECK FOR SHORT)
a.

Disconnect the z17 power steering ECU with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z17)Location & Routing

Click Connector(z17)Instrument Panel>other>Steering Torque Sensor (Rack & Pinion Power Steering Gear Assembly) , Power Steering ECU Assembly

z17-3 (TRQV2) - Body ground Always 10 kΩ or higher
z17-3 (TRQV2) - z17-2 (TRQG2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING ECU WITH MOTOR ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)

NG

2.INSPECT POWER STEERING ECU WITH MOTOR ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)
a.

Start the engine.


b.
C319556C89
1.5,0.292 1.948,0.583 0.448,0.292 2.417,0.656 1.75,1.646 true 0.865,2.74 1.469,1.771 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 2.302,0.49 2.781,0.771 0.479,0.281 10 false TRQG2 0.646,2.76 1.125,3.042 0.479,0.281 10 false TRQV2 1.615,0.344 1.896,0.542 0.281,0.198 10 false z17
*a Component with harness connected
(Power Steering ECU with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z17)Location & Routing

Click Connector(z17)Instrument Panel>other>Steering Torque Sensor (Rack & Pinion Power Steering Gear Assembly) , Power Steering ECU Assembly

z17-3 (TRQV2) - z17-2 (TRQG2) Engine running 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

NG