Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C110E14  Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 1 skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the main relay, the No. 2 skid control ECU (brake actuator assembly) will store a DTC.

If the battery voltage is temporarily low, this DTC may be stored.

HINT:

DTCs C125600 may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C110E14 Brake Booster Motor "A" Supply Voltage Circuit Short to Ground or Open When the voltage at terminal +BI1 is more than 7.3 V, the voltage at terminal MRI1 is less than 5.7 V for 1 second or more.
·

Improperly connected connector, deformation or corrosion of terminals

·

Wire harness and connector

·

Backup boost converter circuit*

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

*: w/ Stop and Start System


WIRING DIAGRAM

C457032E01
2.188,1.552 3.438,1.917 1.25,0.365 10 false ABS MAIN NO. 1 2.063,0.729 3.167,1.01 1.104,0.281 10 false ABS MTR NO. 1 2.156,3.938 3.24,4.198 1.083,0.26 10 false ECU-IGR NO. 3 2.135,4.885 3.177,5.135 1.042,0.25 10 false ENG-IGP NO. 2 4.271,1.25 4.583,1.448 0.313,0.198 10 false 15 4.271,2.115 4.583,2.313 0.313,0.198 10 false 14 4.344,0.427 4.656,0.625 0.313,0.198 10 false 1 4.292,3.635 4.604,3.833 0.313,0.198 10 false 31 4.281,4.583 4.594,4.781 0.313,0.198 10 false 42 4.563,1.479 4.875,1.677 0.313,0.198 10 false BS 4.542,2.323 4.99,2.604 0.448,0.281 10 false +BI1 4.563,0.656 4.99,0.917 0.427,0.26 10 false MRI1 4.552,3.875 4.865,4.073 0.313,0.198 10 false IG1 4.563,4.813 4.875,5.01 0.313,0.198 10 false IG2 4.354,5.354 4.823,5.552 0.469,0.198 10 false B19 4.344,5.542 6.76,5.969 2.417,0.427 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.885,2.781 6.198,2.979 0.313,0.198 10 false IC 3.26,2.094 3.573,2.292 0.313,0.198 10 false *1 2.052,2.406 3.479,2.635 1.427,0.229 10 false ABS MAIN NO. 2 1.865,2.677 2.021,2.875 0.156,0.198 10 false 2 3.906,2.521 4.219,2.719 0.313,0.198 10 false *2 1.458,2.781 1.792,2.99 0.333,0.208 10 false B41 1.854,3.052 2.167,3.25 0.313,0.198 10 false 23 1.427,3.146 2.042,3.344 0.615,0.198 10 false IG31 3.219,3.625 3.531,3.823 0.313,0.198 10 false *1 3.896,3.458 4.208,3.656 0.313,0.198 10 false *2 0.125,3.594 0.583,3.792 0.458,0.198 10 false I57 0.115,3.76 2.01,3.969 1.896,0.208 10 false Engine Stop and Start ECU*2 0.344,5.76 2.708,5.969 2.365,0.208 10 false *1: w/o Stop and Start System 0.333,6.198 2.698,6.406 2.365,0.208 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C110E14 is output A
C110E14 and other DTCs are output B



A

2.CHECK VEHICLE

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

3.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)

B

4.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
3.CHECK HARNESS AND CONNECTOR (+BI1 AND MRI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 11 to 14 V
B19-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+BI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-14 (+BI1) - Body ground Always 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)

NG

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR