Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C051223  Right Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C051212.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C051223 Right Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Rear speed sensor RH

·

Rear speed sensor installation

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C051223 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) - - ○
Detection Time 30 seconds or more. 1 second or more. 30 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C168336C07
0.76,1.917 1.083,2.083 0.323,0.167 10 *a 2.417,1.917 2.74,2.083 0.323,0.167 10 *b
*a Correct
*b Incorrect


Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle carrier RH.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

2.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the rear speed sensor tip RH.

OK:

The rear speed sensor tip RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor RH, clean the rear speed sensor RH.

·

If the rear speed sensor RH is damaged, replace the rear speed sensor RH with a new one.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (RR WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR RH

3.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Perform a road test.


b.

Check the rear speed sensor RH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15
OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
4.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the s1 and Vs1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(s1,Vs1)Location & Routing

Click Connector(s1)Body>No. 1 Parking Brake Wire Assembly>Rear Speed Sensor RH

Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assembly

s1-2 - Vs1-1 Always Below 1 Ω
s1-2 or Vs1-1 - Body ground and other terminals Always 10 kΩ or higher
s1-1 - Vs1-4 Always Below 1 Ω
s1-1 or Vs1-4 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Vs1,B20)Location & Routing

Click Connector(Vs1)Body>Differential Wire / Frame Wire>Frame Wire and No. 1 Parking Brake Wire Assembly

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Vs1-1 - B20-20 (RR+) Always Below 1 Ω
Vs1-1 or B20-20 (RR+) - Body ground Always 10 kΩ or higher
Vs1-4 - B20-19 (RR-) Always Below 1 Ω
Vs1-4 or B20-19 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the rear speed sensor rotor RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>DISASSEMBLY


b.

Check the rear speed sensor rotor RH.

OK:

The rear speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor RH, clean the rear speed sensor rotor RH.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor RH.

·

If the rear speed sensor rotor RH is damaged, replace the rear speed sensor rotor RH with a new one.



HINT:

The rear speed sensor rotor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.



Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor RH.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

C

CLEAN REAR SPEED SENSOR ROTOR RH