Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2021.04–2021.07
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C124A00  ECM Communication  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C124A00 ECM Communication Either of the following is detected:
·

The engine type, powertrain variation and destination information sent from the ECM do not match the information stored in the No. 2 skid control ECU (brake actuator assembly).

·

No system information stored in the No. 2 skid control ECU (brake actuator assembly).


·

Incorrect ECM installed

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C124A00 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The engine type, powertrain variation and destination information sent from the ECM do not match the information stored in the No. 2 skid control ECU (brake actuator assembly) ○ -
No system information stored in the No. 2 skid control ECU (brake actuator assembly) - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK PART NUMBER (ECM)
a.

Check that the proper ECM is installed.

OK:

Proper ECM is installed.



Result:
Proceed to
OK
NG



OK

2.CHECK PART NUMBER (BRAKE ACTUATOR ASSEMBLY)

NG

2.CHECK PART NUMBER (BRAKE ACTUATOR ASSEMBLY)
a.

Check that the proper No. 2 skid control ECU (brake actuator assembly) is installed.

OK:

Proper No. 2 skid control ECU (brake actuator assembly) is installed.



Result:
Proceed to
OK
NG



OK

3.SYSTEM INFORMATION MEMORIZATION

NG

3.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 5560
Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 5554
HINT:

After performing "Reset Memory" using the GTS to clear the memorized value of the No. 2 skid control ECU (brake actuator assembly), DTC C124A00 will be stored until system information memorization is performed.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C124A00 is not output A
C124A00 is output B



A

END

B