Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C140000  Brake Pressure Leak Malfunction  C140A00  Pressure Control Reservoir Leak Malfunction  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Foreign matter enters a solenoid valve.

·

Brake pads are replaced.

·

Rotors are replaced.

HINT:

When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C140000 Brake Pressure Leak Malfunction Malfunction (leakage, etc.) detected in the ABS decrease pressure valve in the brake actuator assembly.
·

Brake booster with master cylinder assembly

·

Brake actuator assembly


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C140A00 Pressure Control Reservoir Leak Malfunction After the vehicle is driven at a certain speed and the ignition switch is turned off for 90 seconds, a malfunction is detected by the No. 2 skid control ECU (brake actuator assembly) during self-diagnosis.
·

Brake booster with master cylinder assembly

·

Brake actuator assembly


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.INSPECT WHEEL CYLINDER PRESSURE
a.

Mount a pedal effort gauge.


b.

Disconnect the B18 brake booster with accumulator pump assembly connector.


c.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster with accumulator pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



d.

Connect an LSPV gauge set.


e.

Slowly depress the brake pedal and check the wheel cylinder pressure with respect to brake pedal depression force.

NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Pressure:
for Front Right Wheel
Brake Effort
[N (kgf, lbf)]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20.4, 45.0) 0.00 to 2.80 (0.0 to 28.6, 0 to 406)
500 (51.0, 112.4) 1.00 to 5.00 (10.2 to 51.0, 145 to 725)

for Rear Right Wheel
Brake Effort
[N (kgf, lbf)]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20.4, 45.0) 0.00 to 2.80 (0.0 to 28.6, 0 to 406)
500 (51.0, 112.4) 1.00 to 5.00 (10.2 to 51.0, 145 to 725)



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

4.INSPECT BRAKE FLUID LEAKS
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C140000 and C140A00 are not output A
C140000 or C140A00 is output B
C140A00 and C139A00 are not output C



A

B

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY

for Brake Booster with Master Cylinder Assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for Brake Booster with Master Cylinder Assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL

for Brake Actuator Assembly (for LHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL

for Brake Actuator Assembly (for RHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL


4.INSPECT BRAKE FLUID LEAKS
a.

Brake fluid leaks and air in brake line inspection

i.

Check and take a note of the fluid level in the brake master cylinder reservoir assembly.


ii.

Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).


iii.

Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.


iv.

If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.



OK:

There are no fluid leaks.


Result:
Proceed to
OK
NG



OK

NG

REPAIR BRAKE FLUID LEAKS AND ADD FLUID