Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C141C12  Brake Booster Motor "A" Control Circuit Short to Battery  C141C14  Brake Booster Motor "A" Control Circuit Short to Ground or Open  C141C1C  Brake Booster Motor "A" Control Circuit Voltage Out of Range  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C141C12 Brake Booster Motor "A" Control Circuit Short to Battery A short is detected in the motor relay drive circuit for 2 seconds or more.
·

Short in pump motor circuit or pump motor monitor circuit

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
C141C14 Brake Booster Motor "A" Control Circuit Short to Ground or Open When the +BI1 voltage is between 7.3 and 16.6 V and the duty ratio of the pump motor is at 100%, the difference between the voltage at terminal MRI1 and the voltage at the pump motor is more than 1.5 V for 0.12 seconds or more.
·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
C141C1C Brake Booster Motor "A" Control Circuit Voltage Out of Range An open is detected in the motor relay drive circuit for 2 seconds or more.
·

Open in pump motor circuit or pump motor monitor circuit

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C141C12, C141C14 or C141C1C is output A
C141C12, C141C14 or C141C1C and other DTCs are output B



A

2.READ VALUE USING GTS (MOTOR RELAY)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.READ VALUE USING GTS (MOTOR RELAY)
a.

Depress the brake pedal several times and check the operation status of the motor relay.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
50003 466 96
HINT:

Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.



Result:
Result Proceed to
The status of motor relay in the Data List turns on and off after depressing the brake pedal several times. A
The status of motor relay in the Data List does not change even after depressing the brake pedal several times. B



A

3.INSPECT BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

B

10.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)
3.INSPECT BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY)

NG

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.




Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ACCUMULATOR PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Reconnect the B18 brake booster with accumulator pump assembly connector.


b.

Reconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the B15 brake pedal stroke sensor assembly connector.


d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


e.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
HINT:
·

This inspection checks whether an accumulator pressure sensor malfunction, internal brake booster with master cylinder assembly leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.

·

If the brake fluid level in the brake fluid level warning switch (brake booster with master cylinder assembly) drops, an external brake fluid leak is suspected.




Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



A

6.CLEAR DTC

B

8.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
6.CLEAR DTC
a.

Turn the ignition switch off.


b.

Reconnect the B15 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
C141C12, C141C14 and C141C1C are not output A
C141C12, C141C14 or C141C1C is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

8.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Turn the ignition switch off.


b.

Reconnect the B15 brake pedal stroke sensor assembly connector.


c.

Drive the linear solenoid (SLA) by performing the Active Test to reduce the accumulator pressure.

HINT:

Perform the Active Test with the current set to maximum.



d.

After reducing the accumulator pressure, confirm that the pump motor starts and the accumulator pressure returns to 15.00 to 21.00 MPa.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLA) Linear solenoid addition valve (SLA) Solenoid Start (Activate)
Solenoid SLA
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLA)
Data List Display
Accumulator Pressure
50004 466 43 212
OK:

The accumulator pressure reduces, and then returns to 15.00 to 21.00 MPa when the pump motor operates.



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.RECONFIRM DTC
a.

Confirm that the pump motor inside the brake booster with accumulator pump assembly is stopped.


b.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


c.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
C141C12, C141C14 and C141C1C are not output A
C141C12, C141C14 or C141C1C is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

B19-1 (MRI1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the B18 brake booster with accumulator pump assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.




Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR