| *A | for V35A-FTS | *B | for 1GR-FE |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *a | For use with SST | *b | For use with union nut wrench |
| ● | Non-reusable part | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
44250 1.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY
2.CONNECT PRESSURE FEED TUBE ASSEMBLY
for V35A-FTS:
| *a | Torque Wrench Fulcrum Length | - | - |
Temporarily install pressure feed tube assembly to the rack and pinion power steering gear assembly.
Install the pressure feed tube assembly with the 3 bolts.
Using a union nut wrench, fully tighten the pressure feed tube assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
Connect the pressure feed tube to the rack and pinion power steering gear assembly with the clip.
for 1GR-FE:
| *a | Torque Wrench Fulcrum Length | - | - |
Temporarily install pressure feed tube assembly to the rack and pinion power steering gear assembly.
Install the pressure feed tube assembly with the 2 bolts.
Using a union nut wrench, fully tighten the pressure feed tube assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
Connect the pressure feed tube to the rack and pinion power steering gear assembly with the clip.
51604 3.INSTALL FRONT BOUND STOPPER BRACKET SUB-ASSEMBLY LH
Install the front bound stopper bracket sub-assembly LH with the 4 bolts.
Install the 4 bolts in the order of (A), (B), (C) and (D).
51603A 4.INSTALL FRONT BOUND STOPPER BRACKET SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
45047 5.CONNECT TIE ROD END SUB-ASSEMBLY LH
Connect the tie rod end sub-assembly LH to the front lower ball joint assembly with the a new nut.
Install a new clip.
Further tighten the nut up to 60° if the holes for the clip are not aligned.
45046 6.CONNECT TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
45203 7.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
| *a | Matchmark | - | - |
If the dust cover was removed, install by aligning with the matchmarks.
Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.
Tighten the No. 2 steering intermediate shaft with the bolt.
Be careful not to damage the dust cover.
41110F 8.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
w/ Differential Lock:
w/o Differential Lock:
9.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
10.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
45047 11.FULLY TIGHTEN TIE ROD END SUB-ASSEMBLY LH
| *a | Torque Wrench Fulcrum Length | *b | Length of 131.5 mm (5.177 in.) |
| *c | 30 mm (1.18 in.) | - | - |
Using SST, tighten the nut of the tie rod end sub-assembly LH.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 131.5 mm (5.177 in.)) + torque wrench (fulcrum length of 255 mm (10.039 in.)): 59.4 N*m (606 kgf*cm, 44 ft.*lbf)
45046 12.FULLY TIGHTEN TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
13.ADD POWER STEERING FLUID
14.BLEED POWER STEERING FLUID
for 1GR-FE:
Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (for 1GR-FE)>ON-VEHICLE INSPECTION
for V35A-FTS:
Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (for V35A-FTS)>ON-VEHICLE INSPECTION
15.CHECK FOR POWER STEERING FLUID LEAKAGE
16.PERFORM INITIALIZATION