Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) Y

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power steering system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY
2.INSPECT BATTERY
a.

Turn the ignition switch off.


b.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC AND FREEZE FRAME DATA*
3.CHECK DTC AND FREEZE FRAME DATA*
a.

Check DTCs and freeze frame data.

i.

Check and record DTCs.

Chassis > PPS > Trouble Codes
50001 405
Chassis > Steering Actuator > Trouble Codes
50001 499



b.

Clear the DTCs and freeze frame data.

Chassis > PPS > Clear DTCs
50002 405
Chassis > Steering Actuator > Clear DTCs
50002 499

c.

Recheck for DTCs.

Chassis > PPS > Trouble Codes
50001 405
Chassis > Steering Actuator > Trouble Codes
50001 499
i.

Reproduce the problem symptoms based on the recorded DTCs and freeze frame data, and then check if the DTCs are output again.

HINT:
·

When DTCs indicating a CAN communication system malfunction are output, first troubleshoot and repair the CAN communication system.

·

If the GTS cannot communicate with the power steering ECU with motor assembly, check CAN communication between the DLC3 and the power steering ECU with motor assembly, and also check the IG circuit of the power steering ECU with motor assembly.

·

If the GTS cannot communicate with the power steering ECU assembly, check CAN communication between the DLC3 and the power steering ECU assembly, and also check the IG circuit of the power steering ECU assembly.





d.

Check the vehicle control history (RoB).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>VEHICLE CONTROL HISTORY (RoB)

Chassis > PPS > Utility
Tester Display
Vehicle Control History (RoB)
50005 405 55
Chassis > Steering Actuator > Utility
Tester Display
Vehicle Control History (RoB)
50005 499 55

Result:
Result Proceed to
DTC is not output but problem symptoms can be reproduced and confirmed A
DTC is output B
DTC is not output and problem symptoms cannot be reproduced and confirmed C
DTC is not output and vehicle control history (RoB) is output D



A

4.PROBLEM SYMPTOMS TABLE

B

REFER TO DIAGNOSTIC TROUBLE CODE CHART, PERFORM TROUBLESHOOTING ACCORDING TO PROCEDURE FOR EACH DTC AND GO TO STEP 7

C

D

PERFORM TROUBLESHOOTING AND REPAIRS RELATED TO VEHICLE CONTROL HISTORY (RoB)

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>VEHICLE CONTROL HISTORY (RoB)

NOTICE:

After performing troubleshooting and repairs related to the vehicle control history (RoB), clear the vehicle control history (RoB).



4.PROBLEM SYMPTOMS TABLE

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B



A

5.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

PERFORM TROUBLESHOOTING ACCORDING TO PROCEDURE FOR EACH CORRESPONDING SYMPTOM AND GO TO STEP 7

5.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

6.REPAIR OR REPLACE
6.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

7.CONFIRMATION TEST
7.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END