Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL PRESSURE SENSOR
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470025 FUEL PRESSURE SENSOR A

V35A-FTS FUEL  FUEL PRESSURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A482129N01
3.927,2.469 4.26,2.26 4.26,2.26 4.427,2.26 false 4.281,1.823 5.031,1.823 false 2.927,2.25 3.177,2.25 3.177,2.25 3.594,2.5 false 0.688,1.333 0.938,1.333 0.938,1.333 1.438,1.083 false 3.833,0.833 4.083,0.833 4.083,0.833 4.333,1.25 false 6.396,0.313 6.813,0.313 false 6.375,0.771 6.771,0.771 false 5.01,0.615 5.281,0.792 0.271,0.177 10 false x 2 5.938,0.156 6.427,0.448 0.49,0.292 18 false 1, 2 6.198,0.635 6.417,0.885 0.219,0.25 18 false 3 0.51,1.188 0.729,1.438 0.219,0.25 18 false 4 3.656,0.688 3.875,0.938 0.219,0.25 18 false 5 2.729,2.115 2.948,2.365 0.219,0.25 18 false 7 5.083,1.677 5.302,1.927 0.219,0.25 18 false 6 4.469,2.156 4.844,2.344 0.375,0.188 10 false ● *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 INTERCOOLER ASSEMBLY 17940D - - -
5 NO. 6 WATER BY-PASS PIPE 1628A - - -
6 NO. 2 FUEL PRESSURE SENSOR HOLDER 23851A - - -
7 NO. 2 FUEL PRESSURE SENSOR 89458H - - -

*1 O-RING - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 2 fuel pressure sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of No. 2 fuel pressure sensor Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17940D 4.REMOVE INTERCOOLER ASSEMBLY

Hide 1628A 5.DISCONNECT NO. 6 WATER BY-PASS PIPE

a.
A482126


Hide 23851A 6.REMOVE NO. 2 FUEL PRESSURE SENSOR HOLDER

a.
A482130


Hide 89458H 7.REMOVE NO. 2 FUEL PRESSURE SENSOR

a.
A482127


b.
A487603