Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469671 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 3 CAN junction connector (for RHD)

·

Open or short in No. 5 global CAN junction connector (for LHD)

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (A)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor LH (B)


Clearance Warning A
U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 3 CAN junction connector (for RHD)

·

Open or short in No. 5 global CAN junction connector (for LHD)

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor LH (B)

·

Blind spot monitor sensor LH (B) ground circuit

·

Blind spot monitor sensor RH (A)


Clearance Warning A

WIRING DIAGRAM

E386359E30
4.271,4.479 5.583,4.844 1.313,0.365 10 false No. 3 CAN Junction Connector*1 4.271,4.292 5.906,4.563 1.635,0.271 10 false I115*1, I166*2 4.115,3.438 4.292,3.635 0.177,0.198 10 false 9 4.063,3.802 4.271,3.979 0.208,0.177 10 false 20 3.792,3.438 4.052,3.677 0.26,0.24 10 false 37 3.792,3.802 4.052,4.042 0.26,0.24 10 false 38 3.302,3.542 3.719,3.74 0.417,0.198 10 false CANH 3.302,3.906 3.781,4.104 0.479,0.198 10 false CANL 2.646,4.406 3.875,4.969 1.229,0.563 10 false Clearance Warning ECU Assembly 2.656,4.24 3.104,4.427 0.448,0.188 10 false I58 4.042,0.833 4.25,1.01 0.208,0.177 10 false 11 4.052,1.448 4.281,1.646 0.229,0.198 10 false 22 5.521,0.813 5.688,0.979 0.167,0.167 10 false 1 5.521,1.438 5.688,1.604 0.167,0.167 10 false 6 3.26,0.833 3.875,1.031 0.615,0.198 10 false CA2P 5.75,0.833 6.156,1.042 0.406,0.208 10 false CA2P 5.75,1.708 6.365,1.906 0.615,0.198 10 false CA2N 3.229,1.729 3.844,1.927 0.615,0.198 10 false CA2N 3.719,0.823 3.99,1.042 0.271,0.219 10 false 1 3.74,1.448 4.01,1.667 0.271,0.219 10 false 6 2.49,1.021 2.76,1.24 0.271,0.219 10 false 5 2.417,1.708 2.688,1.927 0.271,0.219 10 false 10 2.667,1.115 2.969,1.302 0.302,0.188 10 false BLB 2.677,1.802 3.125,2 0.448,0.198 10 false BLGD 6.25,1.833 6.708,2.031 0.458,0.198 10 false BRGD 6.354,1.115 6.729,1.302 0.375,0.188 10 false BRB 6.76,1 6.927,1.188 0.167,0.188 10 false 5 6.74,1.729 7.01,1.948 0.271,0.219 10 false 10 2.563,2.5 3.729,2.896 1.167,0.396 10 false Blind Spot Monitor Sensor LH (B) 2.594,2.323 2.885,2.51 0.292,0.188 10 false T10 5.688,2.323 6,2.521 0.313,0.198 10 false Q21 5.115,1.438 5.323,1.625 0.208,0.188 10 false 21 5.115,0.844 5.323,1.01 0.208,0.167 10 false 10 1.604,0.531 2.198,0.896 0.594,0.365 10 false ECU-IGR NO.2 0.167,0.354 1.156,0.729 0.99,0.375 10 false from IGR-NO. 2 Relay 5.688,2.49 6.844,2.875 1.156,0.385 10 false Blind Spot Monitor Sensor RH (A) 4.302,4.875 5.969,5.271 1.667,0.396 10 false No. 5 Global CAN Junction Connector*2 0.104,4.906 1.74,5.177 1.635,0.271 10 false *1: for RHD 0.104,5.198 1.74,5.469 1.635,0.271 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTCs are not output A
Only U117787 is output B
Only U117887 is output C
U117787 and U117887 are output D



A

B

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)

C

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)

D

13.CHECK CAN BUS MAIN WIRE
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-10 (BRGD) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-5 (BRB) - Body ground Ignition switch ON 11 to 14 V
Q21-5 (BRB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH [A])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH [A])

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-1 (CA2P) - Q21-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

5.CHECK VEHICLE TYPE
5.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for LHD A
for RHD B



A

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

B

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-10 (CANH) - I166-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-10 (CANH) - I115-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - NO. 3 CAN JUNCTION CONNECTOR)

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-10 (BLGD) - Body ground Always Below 1 Ω



Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
T10-5 (BLB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH [B])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH [B])

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-1 (CA2P) - T10-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

10.CHECK VEHICLE TYPE
10.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for LHD A
for RHD B



A

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

B

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 CAN JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-11 (CANH) - I166-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH [A] - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-11 (CANH) - I115-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH [B] - NO. 3 CAN JUNCTION CONNECTOR)

13.CHECK CAN BUS MAIN WIRE

Pre-procedure1

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the I58 clearance warning ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58,I76)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I58-37 (CANH) - I58-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I58-37 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-38 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-37 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I58-38 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
I58-37 (CANH) - I58-38 (CANL) is more than or equal to 70 Ω A
I58-37 (CANH) - I58-38 (CANL) is less than or equal to 54 Ω B
I58-37 (CANH) - I76-4 (CG) is less than or equal to 200 Ω C
I58-38 (CANL) - I76-4 (CG) is less than or equal to 200 Ω D
I58-37 (CANH) - I76-16 (BAT) is less than or equal to 6 kΩ E
I58-38 (CANL) - I76-16 (BAT) is less than or equal to 6 kΩ F
None of the above conditions are met G


Post-procedure1

d.

None



A

14.CHECK VEHICLE TYPE

B

25.CHECK VEHICLE TYPE

C

38.CHECK VEHICLE TYPE

D

38.CHECK VEHICLE TYPE

E

38.CHECK VEHICLE TYPE

F

38.CHECK VEHICLE TYPE

G

14.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for LHD A
for RHD B



A

15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

B

20.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-11 (CANH) - I166-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

16.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
16.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-10 (CANH) - I166-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

17.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

19.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
17.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-9 (CANH) - I166-20 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

18.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-1 (CA2P) - T10-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

19.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-1 (CA2P) - Q21-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

20.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-11 (CANH) - I115-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

21.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

NG

23.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
21.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-10 (CANH) - I115-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

22.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

NG

24.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
22.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-9 (CANH) - I115-20 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

NG

REPLACE NO. 3 CAN JUNCTION CONNECTOR

23.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-1 (CA2P) - T10-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 3 CAN JUNCTION CONNECTOR)

24.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-1 (CA2P) - Q21-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 3 CAN JUNCTION CONNECTOR)

25.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for LHD A
for RHD B



A

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

B

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-11 (CANH) - I166-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

29.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-10 (CANH) - I166-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

30.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

I166-9 (CANH) - I166-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

31.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
29.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-1 (CA2P) - T10-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

30.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-1 (CA2P) - Q21-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the I58 clearance warning ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

I58-37 (CANH) - I58-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-11 (CANH) - I115-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

NG

35.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-10 (CANH) - I115-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

NG

36.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

I115-9 (CANH) - I115-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

37.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
35.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

T10-1 (CA2P) - T10-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 3 CAN JUNCTION CONNECTOR)

36.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Q21-1 (CA2P) - Q21-6 (CA2N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 3 CAN JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the I58 clearance warning ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

I58-37 (CANH) - I58-38 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

38.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for LHD A
for RHD B



A

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

B

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166,I76)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I166-11 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-22 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-11 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I166-22 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

42.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166,I76)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I166-10 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-21 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-10 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I166-21 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

NG

43.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I166 No. 5 global CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I166,I76)Location & Routing

Click Connector(I166)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 5 Global CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I166-9 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-20 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I166-9 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I166-20 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE NO. 5 GLOBAL CAN JUNCTION CONNECTOR

NG

44.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
42.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10,I76)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

T10-1 (CA2P) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-6 (CA2N) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-1 (CA2P) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T10-6 (CA2N) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

43.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21,I76)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q21-1 (CA2P) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q21-6 (CA2N) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q21-1 (CA2P) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q21-6 (CA2N) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

44.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the I166 No. 5 global CAN junction connector.


b.

Disconnect the I58 clearance warning ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58,I76)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I58-37 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-38 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-37 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I58-38 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 5 GLOBAL CAN JUNCTION CONNECTOR)

45.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115,I76)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I115-11 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-22 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-11 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I115-22 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

NG

48.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
46.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115,I76)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I115-10 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-21 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-10 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I115-21 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

NG

49.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
47.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION CONNECTOR)

Pre-procedure1

a.

Disconnect the I115 No. 3 CAN junction connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I115,I76)Location & Routing

Click Connector(I115)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 3 CAN Junction Connector

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I115-9 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-20 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I115-9 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I115-20 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG

50.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
48.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10,I76)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

T10-1 (CA2P) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-6 (CA2N) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-1 (CA2P) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T10-6 (CA2N) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 3 CAN JUNCTION CONNECTOR)

49.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21,I76)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

Q21-1 (CA2P) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q21-6 (CA2N) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q21-1 (CA2P) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q21-6 (CA2N) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 3 CAN JUNCTION CONNECTOR)

50.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the I115 No. 3 CAN junction connector.


b.

Disconnect the I58 clearance warning ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I58,I76)Location & Routing

Click Connector(I58)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Clearance Warning ECU Assembly

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I58-37 (CANH) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-38 (CANL) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-37 (CANH) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I58-38 (CANL) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)