Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)
RM38G0E _59 Vehicle Exterior _100827 MIRROR (EXT) _0468036 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH


B343031E61
4.427,0.083 4.844,0.333 0.417,0.25 2.406,0.083 2.823,0.333 0.417,0.25 4.552,0.135 5.01,0.333 0.458,0.198 10 false N1 2.51,0.125 2.969,0.323 0.458,0.198 10 false z10

a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
N1-14 (BDR) - Body ground +B power supply Always 11 to 14 V
N1-6 (CPUB) - Body ground +B power supply Always 11 to 14 V
N1-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
N1-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N1 outer mirror control ECU assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: w/ Mirror Heater

*2: w/ Memory

z10-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly LH being retracted 11 to 14 V
Outer rear view mirror assembly LH stopped Below 1 V
z10-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly LH returning 11 to 14 V
Outer rear view mirror assembly LH stopped Below 1 V
z10-1 (MV) - z10-10 (M+) Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z10-10 (M+) - z10-1 (MV) Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z10-10 (M+) - z10-9 (MH) Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z10-9 (MH) - z10-10 (M+) Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z10-5 (VC) - z10-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z10-6 (VSSR) - N1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z10-13 (HSSR) - N1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z10-7 (EC+) - z10-15 (EC-) Automatic glare-resistant EC mirror drive signal Automatic glare-resistant EC mirror off → on Below 1 V → 1.05 to 1.35 V
z10-4 (+) - z10-12 (H/T-)*1 Mirror heater relay drive voltage Mirror heater switch (window defogger switch) on 11 to 14 V
N1-4 (M3) - N1-7 (GND)*2 M3 switch signal for seat memory switch M3 switch on Below 1 V
M3 switch off 11 to 14 V
N1-3 (M2) - N1-7 (GND)*2 M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
N1-2 (M1) - N1-7 (GND)*2 M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
N1-1 (MM) - N1-7 (GND)*2 SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Mirror Heater

z10-3 (MR) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly LH being retracted 11 to 14 V
Outer rear view mirror assembly LH stopped Below 1 V
z10-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly LH returning 11 to 14 V
Outer rear view mirror assembly LH stopped Below 1 V
z10-1 (MV) - z10-10 (M+) Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z10-10 (M+) - z10-1 (MV) Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z10-10 (M+) - z10-9 (MH) Horizontal mirror motor drive voltage Front passenger mirror surface moving right → stopped 11 to 14 V → Below 1 V
z10-9 (MH) - z10-10 (M+) Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z10-5 (VC) - z10-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z10-6 (VSSR) - N1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z10-13 (HSSR) - N1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z10-7 (EC+) - z10-15 (EC-) Automatic glare-resistant EC mirror drive signal Automatic glare-resistant EC mirror off → on Below 1 V → 1.05 to 1.35 V
z10-4 (+) - z10-12 (H/T-)* Mirror heater relay drive voltage Mirror heater switch (window defogger switch) on 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH


B343031E62
4.406,0.083 4.823,0.333 0.417,0.25 2.344,0.083 2.76,0.333 0.417,0.25 4.521,0.125 4.979,0.323 0.458,0.198 10 false M1 2.49,0.125 2.948,0.323 0.458,0.198 10 false z9

a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
M1-14 (BDR) - Body ground +B power supply Always 11 to 14 V
M1-6 (CPUB) - Body ground +B power supply Always 11 to 14 V
M1-5 (SIG) - Body ground Ignition power supply Ignition switch off → ON Below 1 V → 11 to 14 V
M1-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the M1 outer mirror control ECU assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*: w/ Mirror Heater

z9-3 (MR+) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly RH being retracted 11 to 14 V
Outer rear view mirror assembly RH stopped Below 1 V
z9-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly RH returning 11 to 14 V
Outer rear view mirror assembly RH stopped Below 1 V
z9-1 (MV) - z9-10 (M+) Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z9-10 (M+) - z9-1 (MV) Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z9-10 (M+) - z9-9 (MH) Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z9-9 (MH) - z9-10 (M+) Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z9-5 (VC) - z9-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z9-6 (VSSR) - M1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z9-13 (HSSR) - M1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z9-7 (EC+) - z9-15 (EC-) Automatic glare-resistant EC mirror drive signal Automatic glare-resistant EC mirror off → on Below 1 V → 1.05 to 1.35 V
z9-4 (+) - z9-12 (H/T-)* Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: w/ Mirror Heater

*2: w/ Memory

z9-3 (MR+) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly RH being retracted 11 to 14 V
Outer rear view mirror assembly RH stopped Below 1 V
z9-11 (MF) - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly RH returning 11 to 14 V
Outer rear view mirror assembly RH stopped Below 1 V
z9-1 (MV) - z9-10 (M+) Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
z9-10 (M+) - z9-1 (MV) Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
z9-10 (M+) - z9-9 (MH) Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
z9-9 (MH) - z9-10 (M+) Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
z9-5 (VC) - z9-14 (E1) Mirror position sensor power supply Ignition switch ON 4.55 to 5.45 V
Ignition switch off Below 1 V
z9-6 (VSSR) - M1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z9-13 (HSSR) - M1-7 (GND) Mirror position sensor signal Ignition switch ON 0 to 5 V
z9-7 (EC+) - z9-15 (EC-) Automatic glare-resistant EC mirror drive signal Automatic glare-resistant EC mirror off → on Below 1 V → 1.05 to 1.35 V
z9-4 (+) - z9-12 (H/T-)*1 Mirror heater relay drive voltage Mirror heater switch (rear window defogger switch) on 11 to 14 V
M1-4 (M3) - M1-7 (GND)*2 M3 switch signal for seat memory switch M3 switch on Below 1 V
M3 switch off 11 to 14 V
M1-3 (M2) - M1-7 (GND)*2 M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
M1-2 (M1) - M1-7 (GND)*2 M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
M1-1 (MM) - M1-7 (GND)*2 SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V



CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E448686C09
3.417,7.583 3.813,7.854 0.396,0.271 5.594,3.219 6.01,3.458 0.417,0.24 1.146,3.198 1.563,3.438 0.417,0.24 1.219,4.469 1.635,4.708 0.417,0.24 1.458,6.042 1.875,6.281 0.417,0.24 3.615,6.063 4.031,6.302 0.417,0.24 4.385,4.458 4.802,4.698 0.417,0.24 6.375,6.073 6.792,6.313 0.417,0.24 4.719,6.094 5.135,6.333 0.417,0.24 6.208,4.479 6.625,4.719 0.417,0.24 5.49,6.094 5.906,6.333 0.417,0.24 3.469,3.198 3.885,3.438 0.417,0.24 2.219,0.917 2.219,0.698 2.219,0.698 2.385,0.698 true 0.646,1.229 0.927,1.229 true 2.229,1.51 2.469,1.51 true 2.219,1.802 2.458,1.802 true 0.646,2.073 0.885,2.073 true 0.635,2.302 0.875,2.302 true 0.646,2.542 1.125,2.542 true 0.635,1.698 0.917,1.698 true 6.292,1.156 6.573,1.156 true 6.271,1.75 6.552,1.75 true 6.292,2.208 6.573,2.208 true 2.229,2.125 2.469,2.125 true 1.177,0.542 1.177,0.323 1.177,0.323 1.344,0.323 true 4.865,0.563 4.865,0.344 4.865,0.344 5.031,0.344 true 6.146,0.51 6.146,0.292 6.146,0.292 6.313,0.292 true 4.271,1.021 4.458,1.292 0.188,0.271 10 false A 3.573,7.625 3.865,7.813 0.292,0.188 10 false A 0.396,1.604 0.708,1.802 0.313,0.198 10 false 5E 0.396,1.99 0.708,2.188 0.313,0.198 10 false 5K 2.552,2.031 3.01,2.229 0.458,0.198 10 false I3 2.542,1.719 3,1.917 0.458,0.198 10 false I2 0.406,2.208 0.906,2.438 0.5,0.229 10 false 5J 2.479,0.594 2.938,0.792 0.458,0.198 10 false *2 6.656,1.073 6.969,1.271 0.313,0.198 10 false 5C 6.646,1.656 6.958,1.854 0.313,0.198 10 false 5B 1.292,3.24 1.75,3.438 0.458,0.198 10 false I3 3.635,3.229 4.094,3.427 0.458,0.198 10 false I2 1.354,4.51 1.667,4.708 0.313,0.198 10 false 5C 4.51,4.5 4.823,4.698 0.313,0.198 10 false 5B 1.583,6.073 1.896,6.271 0.313,0.198 10 false 5F 3.729,6.104 4.042,6.302 0.313,0.198 10 false 5E 6.49,6.115 6.802,6.313 0.313,0.198 10 false 5H 4.833,6.125 5.188,6.281 0.354,0.156 10 false 5K 0.406,1.135 1.021,1.333 0.615,0.198 10 false 5F 0.396,2.458 0.896,2.688 0.5,0.229 10 false 5H 6.656,2.115 6.969,2.313 0.313,0.198 10 false 5A 6.333,4.51 6.646,4.708 0.313,0.198 10 false 5A 5.625,6.125 5.938,6.323 0.313,0.198 10 false 5J 2.552,1.417 3.01,1.615 0.458,0.198 10 false I1 5.76,3.25 6.219,3.448 0.458,0.198 10 false I1 1.448,0.229 1.906,0.427 0.458,0.198 10 false *1 5.125,0.24 5.583,0.438 0.458,0.198 10 false *1 6.385,0.188 6.844,0.385 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



b.

Connect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-26 (BECU) - Body ground Battery power supply Always 11 to 14 V
A-27 (IGR) - Body ground Power source (IG) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A-13 (GND1) - Body ground Ground Always Below 1 Ω
A-14 (GND2) - Body ground Ground Always Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.



e.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I1-22 (MIRB) - I1-21 (MIRE) Mirror adjust switch signal
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch up


Below 1.7 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch right


Below 2.7 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch down


Below 3.5 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch left


Below 4 V
·

Ignition switch ACC

·

Mirror select switch L or R

·

Mirror adjust switch off


11 to 14 V
I1-20 (MIRS) - I1-21 (MIRE) Mirror select switch signal
·

Ignition switch ACC

·

Mirror select switch L


Below 2 V
·

Ignition switch ACC

·

Mirror select switch R


Below 1 V
·

Ignition switch ACC

·

Mirror select switch off


11 to 14 V
I2-27 (RET) - I1-21 (MIRE) Retractable outer mirror switch signal
·

Ignition switch ACC

·

Retractable outer mirror switch not in return position


Pulse generation (See waveform 1 or 2)
·

Ignition switch ACC

·

Retractable outer mirror switch in return position


Below 1 V
I2-26 (AMR) - I1-21 (MIRE) Retractable outer mirror switch signal
·

Ignition switch ACC

·

Retractable outer mirror switch not in return position


Pulse generation (See waveform 1 or 2)
·

Ignition switch ACC

·

Retractable outer mirror switch in return position


Below 1 V


f.
B244640E02
0.135,1.198 0.594,1.396 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Tester Connection I2-27 (RET) or I2-26 (AMR) - I1-21 (MIRE)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ACC

·

Retractable outer mirror switch not in return position




g.
B244641E02
0.135,0.979 0.594,1.177 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Tester Connection I2-27 (RET) or I2-26 (AMR) - I1-21 (MIRE)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Ignition switch ACC

·

Retractable outer mirror switch not in retract position