Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P008800  Fuel Rail / System Pressure - Too High  


DESCRIPTION

Refer to DTC P008700.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P008700

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P008800 Fuel Rail / System Pressure - Too High Although the ECM is requesting the fuel pump assembly (for high pressure side) to open the spill control valve, fuel pressure increases 3 MPa (30.6 kgf/cm2, 435 psi) from target pressure for about 10 seconds (1 trip detection logic).
·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (for high pressure side)

·

ECM


Comes on SAE: P0088

MONITOR DESCRIPTION

If the fuel pressure (for high pressure side) increases despite a decrease request signal being sent to the fuel pump assembly (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor (for high pressure side)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the Freeze Frame Data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Start the engine.

8.

Turn the GTS on.

9.

Based on the engine speed, engine load, injection mode and other conditions displayed in the Freeze Frame Data, reproduce the conditions present when the DTC was stored.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P008800.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008800)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P008800 is output A
P008800 and other DTCs are output B


HINT:

If any DTCs other than P008800 are output, troubleshoot those DTCs first.




A

2.INSPECT FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

B

GO TO DTC CHART

2.INSPECT FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)
a.

Start the engine.


b.

According to the display on the GTS, read the Data List while racing the engine.

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265
OK:

Fuel pressure fluctuates.



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

3.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) (FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY)

NG

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

3.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) (FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY)
HINT:

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for High Pressure)>REMOVAL

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008800 IS OUTPUT AGAIN)
5.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008800 IS OUTPUT AGAIN)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P008800 is output B




A

END

B