Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL PRESSURE SENSOR (for High Pressure)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470026 FUEL PRESSURE SENSOR(for High Pressure) A

V35A-FTS FUEL  FUEL PRESSURE SENSOR(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487394N01
3.323,1.531 3.781,1.531 false 4.406,3.75 4.719,3.927 4.719,3.927 4.885,3.927 false 5.99,3.792 5.823,3.792 5.823,3.792 5.406,3.542 false 5.656,3.146 5.49,3.146 5.49,3.146 5.25,2.865 false 5.875,2.896 6.292,2.646 6.292,2.646 6.542,2.646 false 6.313,0.25 6.813,0.25 false 6.354,0.708 6.771,0.708 false 1.438,3 1.604,3 1.604,3 1.938,3.396 false 3.552,2.281 3.719,2.281 3.719,2.281 3.969,2.948 false 4.75,2.271 4.958,1.688 4.958,1.688 5.125,1.688 false 6.177,4.333 5.771,4.333 false 3.635,1.104 3.115,1.104 false 3.354,2.667 3.604,2.833 0.25,0.167 10 false x 8 6.594,2.542 6.813,2.708 0.219,0.167 10 false *1 5.688,3.042 5.906,3.208 0.219,0.167 10 false *2 6.031,3.698 6.25,3.865 0.219,0.167 10 false *3 4.927,3.813 5.313,3.99 0.385,0.177 10 false ● *4 4.292,0.458 4.542,0.625 0.25,0.167 10 false x 2 6.167,0.563 6.385,0.823 0.219,0.26 18 false 3 5.854,0.094 6.333,0.354 0.479,0.26 18 false 1, 2 1.25,2.854 1.469,3.115 0.219,0.26 18 false 4 5.177,1.542 5.396,1.802 0.219,0.26 18 false 5 3.354,2.125 3.573,2.385 0.219,0.26 18 false 6 6.479,4.188 6.698,4.448 0.219,0.26 18 false 7 2.927,0.958 3.146,1.219 0.219,0.26 18 false 8 2.854,1.406 3.417,1.677 0.563,0.271 18 false ● 9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY 22030 - - -
5 NO. 3 TURBO PRESSURE SENSOR 89421Q - - -
6 INTAKE AIR SURGE TANK ASSEMBLY 17190 - - -
7 FUEL TUBE SUB-ASSEMBLY 23910A (Click here) - -
8 NO. 1 FUEL PRESSURE SENSOR HOLDER 23851 - - -
9 FUEL PRESSURE SENSOR 89458 (Click here) - -

*1 NO. 3 TURBO WATER PIPE SUB-ASSEMBLY *2 VENTILATION HOSE
*3 NO. 3 VAPOR FEED HOSE *4 GASKET
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pressure sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel pressure sensor Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 22030 4.REMOVE THROTTLE WITH THROTTLE POSITION SENSOR BODY ASSEMBLY

Hide 17190 6.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 23910A 7.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A482131N01
1.906,0.083 2.115,0.333 0.208,0.25 18 false i

i.

Disconnect the fuel tube sub-assembly from the No. 1 fuel delivery pipe sub-assembly RH.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 23851 8.REMOVE NO. 1 FUEL PRESSURE SENSOR HOLDER

a.
A487391


Hide 89458 9.REMOVE FUEL PRESSURE SENSOR

Z101186

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



a.
A487392N01
1.906,0.083 2.073,0.344 0.167,0.26 18 false i

i.

Remove the fuel pressure sensor from the No. 2 fuel delivery pipe sub-assembly RH.

NOTICE:
·

Pull and remove the fuel pressure sensor in a straight line to avoid damaging the seal surface of the No. 2 fuel delivery pipe sub-assembly O-ring.

·
A487571C01
1.865,1.646 2.417,1.427 2.417,1.427 2.656,1.427 false 1.542,1.729 0.844,1.729 false 2.688,1.323 3,1.479 0.313,0.156 10 false *a 0.667,1.635 0.979,1.792 0.313,0.156 10 false *b 0.156,0.146 0.469,0.302 0.313,0.156 10 false *1
*1 Fuel Pressure Sensor
*a No. 1 Back-up Ring
*b O-Ring


After removing the fuel pressure sensor, remove any O-ring and No. 1 back-up ring remaining on the No. 2 fuel delivery pipe sub-assembly RH side, do not damage the sealing surface.