Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL PUMP (for High Pressure)
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470028 FUEL PUMP(for High Pressure) A

V35A-FTS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A487423N01
2.688,3.76 3.354,3.76 false 6.24,0.271 6.823,0.271 false 6.281,0.667 6.781,0.667 false 3.99,1.583 4.458,1.583 false 2.563,1.74 3.063,1.74 false 0.583,1.667 1.052,1.667 false 2.729,2.292 3.229,2.292 false 2.156,2.615 2.74,2.615 false 2.375,3.146 2.958,3.146 false 3.344,0.833 4.177,0.833 false 1.594,1.979 1.854,2.156 0.26,0.177 10 false x 2 5.75,0.135 6.25,0.417 0.5,0.281 18 false 1, 2 6.083,0.521 6.313,0.781 0.229,0.26 18 false 3 3.802,1.427 4.031,1.688 0.229,0.26 18 false 4 4.531,0.688 4.76,0.948 0.229,0.26 18 false 5 0.385,1.542 0.615,1.802 0.229,0.26 18 false 6 3.104,1.594 3.333,1.854 0.229,0.26 18 false 7 3.281,2.188 3.677,2.385 0.396,0.198 10 false ● *1 2.208,3.063 2.448,3.24 0.24,0.177 10 false *2 2.25,3.604 2.74,3.865 0.49,0.26 18 false ● 8 1.979,2.469 2.208,2.729 0.229,0.26 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 DISCHARGE FUEL SYSTEM PRESSURE - (Click here) - -
2 PRECAUTION - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
4 INTAKE MANIFOLD 17111 - - -
5 FUEL TUBE SUB-ASSEMBLY 23910A (Click here) - -
6 NO. 1 FUEL PIPE SUB-ASSEMBLY 23801P (Click here) - -
7 FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY 23100X - - -
8 FUEL PUMP SPACER GASKET 23224D - - -
9 FUEL PUMP LIFTER ASSEMBLY 23470 - - -

*1 O-RING *2 FUEL PUMP SPACER
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel (engine room side) pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel (engine room side) pump assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 23910A 5.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A487424N01
2.146,0.115 2.344,0.354 0.198,0.24 18 false i

i.

Remove the fuel tube sub-assembly from the fuel (engine room side) pump assembly and fuel inlet pipe sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 23801P 6.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Z101186

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



a.
A487414N01
0.385,0.344 0.583,0.583 0.198,0.24 18 true i 2.729,0.333 2.927,0.573 0.198,0.24 18 true ii 5.167,0.323 5.365,0.563 0.198,0.24 18 true iii

i.

Using a 17 mm union nut wrench, loosen the union nut and disconnect the No. 1 fuel pipe sub-assembly from the fuel (engine room side) pump assembly.


ii.

Using a 17 mm union nut wrench, loosen the union nut and disconnect the No. 1 fuel pipe sub-assembly from the No. 2 fuel delivery pipe sub-assembly RH.


iii.

Remove the bolt and No. 1 fuel pipe sub-assembly from the cylinder head cover sub-assembly RH.



Hide 23100X 7.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

a.
A487416


Hide 23224D 8.REMOVE FUEL PUMP SPACER GASKET

a.
A487417


Hide 23470 9.REMOVE FUEL PUMP LIFTER ASSEMBLY

a.
A487604