Refer to DTC P010511.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P010511
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P010515 | Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open | The No. 3 turbo pressure sensor output voltage is higher than 4.2 V for 3 seconds or more (1 trip detection logic). |
·
Open or short in No. 3 turbo pressure sensor circuit
·
No. 3 turbo pressure sensor
·
ECM |
Comes on | SAE: P0108 |
When a DTC is output, check the Data List item "Intake Manifold Absolute Pressure" using the GTS.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | Intake Manifold Absolute Pressure | Malfunction |
|---|---|---|
| P010515 | Higher than 278 kPa (40.31 psi) |
·
Short in VCPM to PIM circuit
·
Open in PIM circuit
·
Open in EPIM circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
The ECM monitors the No. 3 turbo pressure sensor voltage and uses this value to calculate the intake manifold pressure. When the No. 3 turbo pressure sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the No. 3 turbo pressure sensor circuit, illuminates the MIL and stores a DTC.
Example:
If the sensor output voltage is higher than 4.2 V for 3 seconds or more, the ECM stores this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait 5 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P010515.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
Refer to DTC P010511.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P010511
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the No. 3 turbo pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C40)Location & Routingewd_type=routing;type=c;code=C40 |
||
| C40-3 (VC) - C40-2 (E2) | Ignition switch ON | 4.75 to 5.25 V |
| C40-1 (PIM) - C40-2 (E2) | Ignition switch ON | 1.2 to 5.25 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C40)Location & Routingewd_type=routing;type=c;code=C40 |
||
| C40-2 (E2) - Body ground | Always | Below 1 Ω |
| C40-3 (VC) - C40-1 (PIM) | Ignition switch off | 171 to 189 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
NG
Disconnect the No. 3 turbo pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C40,C38)Location & Routingewd_type=routing;type=c,c;code=C40,C38 |
||
| C40-2 (E2) - C38-39 (EPIM) | Always | Below 1 Ω |
| C40-1 (PIM) - C38-38 (PIM) | Always | Below 1 Ω |
| C40-1 (PIM) or C38-38 (PIM) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG