Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P032511  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground  P033011  Knock Sensor 2 Bank 2 Circuit Short to Ground  


DESCRIPTION

A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 and 15 kHz.

The knock control sensor is fitted onto the engine block to detect engine knocking.

The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

HINT:

When DTC P032511 or P033011 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P032511 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground The knock control sensor (bank 1) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor (bank 1) circuit

·

Knock control sensor (bank 1)

·

ECM


Comes on SAE: P0327
P033011 Knock Sensor 2 Bank 2 Circuit Short to Ground The knock control sensor (bank 2) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor (bank 2) circuit

·

Knock control sensor (bank 2)

·

ECM


Comes on SAE: P0332

Reference: Inspection using an oscilloscope

A283572E29
2.615,1 3.115,1.292 0.5,0.292 10 false GND

HINT:

The correct waveform is as shown.


ECM Terminal Name Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up the engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock control sensor remains low for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and wait 5 minutes.

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P032511 or P033011.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A361590E32
0.469,1.385 0.781,1.583 0.313,0.198 10 false C10 0.448,3.76 0.76,3.958 0.313,0.198 10 false C9 0.469,1.552 2.948,1.771 2.479,0.219 10 false Knock Control Sensor (Bank 1) 0.448,3.917 2.927,4.135 2.479,0.219 10 false Knock Control Sensor (Bank 2) 0.365,0.885 0.677,1.083 0.313,0.198 10 false 1 0.365,3.26 0.677,3.458 0.313,0.198 10 false 1 2.094,0.885 2.406,1.083 0.313,0.198 10 false 2 2.094,3.271 2.406,3.469 0.313,0.198 10 false 2 4.052,2.302 4.365,2.5 0.313,0.198 10 false * 4.031,4.656 4.344,4.854 0.313,0.198 10 false * 0.896,5.385 2.021,5.667 1.125,0.281 10 false *: Shielded 5.385,0.865 5.698,1.063 0.313,0.198 10 false 122 5.385,1.656 5.719,1.844 0.333,0.188 10 false 121 5.406,3.24 5.656,3.438 0.25,0.198 10 false 120 5.417,4.042 5.667,4.24 0.25,0.198 10 false 119 5.823,0.865 6.26,1.063 0.438,0.198 10 false KNK1 5.813,3.25 6.25,3.448 0.438,0.198 10 false KNK2 5.823,1.656 6.26,1.854 0.438,0.198 10 false EKNK 5.813,4.042 6.25,4.24 0.438,0.198 10 false EKN2 6.031,4.802 6.469,5 0.438,0.198 10 false C37 6.031,4.979 6.656,5.406 0.625,0.427 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P032511 Bank 1
P033011 Bank 2



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)

OK

2.INSPECT KNOCK CONTROL SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
2.INSPECT KNOCK CONTROL SENSOR

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>KNOCK SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock control sensor.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)

OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR P033011)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR P033011)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P032511 or P033011 is output B




A

B