Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P123513  High Pressure Fuel Pump Circuit Open  


DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor (for high pressure side), fuel pump assembly (for high pressure side) and direct fuel injector assemblies. The spill control valve adjusts the return volume of the high-pressure fuel. The check valve mechanically opens and closes the paths to the fuel delivery pipes. The relief valve releases the fuel back to the fuel tank if the high-pressure fuel system malfunctions. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the exhaust camshaft (bank 1). Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P123513 High Pressure Fuel Pump Circuit Open Open or short in fuel pump assembly (for high pressure side) circuit detected 60 times or more (1 trip detection logic).
·

Open or short in fuel pump assembly (for high pressure side) circuit

·

Fuel pump assembly (for high pressure side)

·

ECM


Comes on SAE: P1235

MONITOR DESCRIPTION

If an open or short in the fuel pump assembly (for high pressure side) circuit is detected after the engine is started, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Fuel pump assembly (for high pressure side)
Required Sensors/Components (Related) Injector driver (ECM)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 10 seconds [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P123513.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A384830E07
1.844,0.854 2,1.052 0.156,0.198 10 false 2 0.365,2.313 3.24,2.604 2.875,0.292 10 false Fuel Pump assembly (for High Pressure Side) 3.542,2.021 3.698,2.219 0.156,0.198 10 false * 5.292,1.625 5.698,1.844 0.406,0.219 10 false FP1- 5.292,0.958 5.74,1.177 0.448,0.219 10 false FP1+ 5.625,2.344 6.031,2.563 0.406,0.219 10 false ECM 4.177,2.438 4.906,2.729 0.729,0.292 10 false *: Shielded 0.354,2.146 1.302,2.365 0.948,0.219 10 false C43 5.625,2.167 6.031,2.385 0.406,0.219 10 false C37 5.01,1.49 5.417,1.708 0.406,0.219 10 false 10 5,0.823 5.406,1.042 0.406,0.219 10 false 11 1.833,1.51 1.99,1.708 0.156,0.198 10 false 1 1.479,1.521 1.885,1.74 0.406,0.219 10 false FP- 1.438,0.854 1.844,1.073 0.406,0.219 10 false FP+

CAUTION / NOTICE / HINT

HINT:
·

If the current from the EDU relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL PUMP (for High Pressure)>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)

NG

REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) (FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pump assembly (for high pressure side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C43,C37)Location & Routing

Click Connector(C43)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Fuel Pump Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C43-2 (FP+) - C37-11 (FP1+) Always Below 1 Ω
C43-1 (FP-) - C37-10 (FP1-) Always Below 1 Ω
C43-2 (FP+) or C37-11 (FP1+) - Body ground and other terminals Always 10 kΩ or higher
C43-1 (FP-) or C37-10 (FP1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR