Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P048012  Fan 1 Control Circuit High Circuit Short to Battery  


DESCRIPTION

The electronic control coupling fan can change the oil level as required to control the fan speed to the target value by changing the oil supply valve of the coupling fan from the conventional bimetal type to an electronic control solenoid type.

The electric control coupling fan reduces fan noise and improves fuel economy by reducing the fan speed when not needed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P048012 Fan 1 Control Circuit High Circuit Short to Battery Short circuit in fan control solenoid circuit and power supply circuit (1 trip detection logic).
·

Short in fan control solenoid circuit

·

Fan control solenoid (fluid coupling assembly)

·

ECM


- SAE: P0692

MONITOR DESCRIPTION

The ECM monitors the output voltage while the fan control solenoid is operating.

The fan control solenoid turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the fan control solenoid circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine [A].

7.

Wait 2 minutes or more [B].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P048012.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

A480013E01
0.531,3 1.198,3.271 0.667,0.271 10 false Battery 0.354,1.969 1.583,2.24 1.229,0.271 10 false SUB R/B-NO. 1 0.333,0.938 1.385,1.219 1.052,0.281 10 false EFI MAIN NO. 1 1.688,1.135 2.74,1.448 1.052,0.313 10 false EFI MAIN NO. 1 1.208,0.438 1.927,0.667 0.719,0.229 10 false EFI NO. 2 2.938,0.938 3.927,1.167 0.99,0.229 10 false EFI-B NO. 4 6.323,1.198 6.781,1.396 0.458,0.198 10 false CFDS 6.323,0.292 6.781,0.49 0.458,0.198 10 false MREL 6.313,2.729 6.771,2.927 0.458,0.198 10 false E1 5.969,0.292 6.26,0.51 0.292,0.219 10 false B1 6,2.74 6.292,2.958 0.292,0.219 10 false B1 6.021,0.083 6.219,0.281 0.198,0.198 10 false 3 6.042,1.115 6.24,1.313 0.198,0.198 10 false 2 6.042,2.542 6.24,2.74 0.198,0.198 10 false 9 5.958,1.323 6.25,1.542 0.292,0.219 10 false C38 6.51,3.229 6.885,3.458 0.375,0.229 10 false ECM 4.24,1.635 4.615,1.865 0.375,0.229 10 false C8 4.24,1.802 5.875,2.229 1.635,0.427 10 false Fan Control Solenoid (Fluid Coupling Assembly) 2.51,0.677 2.708,0.875 0.198,0.198 10 false 5 5.521,1.177 5.719,1.375 0.198,0.198 10 false 3 1.813,0.135 2.01,0.333 0.198,0.198 10 false 1 2.531,0.146 2.729,0.344 0.198,0.198 10 false 2 1.823,0.667 2.021,0.865 0.198,0.198 10 false 3 4.219,1.177 4.417,1.375 0.198,0.198 10 false 1 5.021,1.188 5.479,1.385 0.458,0.198 10 false GDFC 4.438,1.188 4.833,1.375 0.396,0.188 10 false EFC+

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

OK

2.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

NG

REPLACE FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048012)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P048012)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P048012 is output B




A

B