Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P007A15  Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P007A11.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P007A11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P007A15 Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open The output voltage from the intake air temperature sensor is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (No. 3 turbo pressure sensor)

·

ECM


- SAE: P007D

HINT:

When a DTC is output, check the Data List item "Intake Air Temperature B1S1 (Turbo)" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Intake Air Temperature B1S1 (Turbo) Malfunction
P007A15 -40°C (-40°F)
·

Short in THIM circuit to power source circuit

·

Open in THIM circuit

·

Open in EPIM circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the intake manifold internal temperature from the intake air temperature sensor output voltage. If the intake air temperature sensor output voltage is outside the normal range, there may be a malfunction or open or short circuit in the intake air temperature sensor. In this case, the ECM stores a DTC.

Example:

If the sensor output voltage is higher than 4.9 V for 3 seconds or more, the ECM stores DTC P007A15.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P007A15.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A358782C10
0.365,3.375 0.76,3.688 0.396,0.313 1.135,4.302 1.51,3.615 true 2.448,4.333 2.198,3.604 true 0.729,1.521 1.042,1.677 0.313,0.156 10 false *1 2.635,1.531 2.948,1.688 0.313,0.156 10 false *2 0.229,2.542 0.542,2.698 0.313,0.156 10 false *a 2.031,0.573 2.406,0.792 0.375,0.219 10 false THIM 2.01,0.938 2.385,1.156 0.375,0.219 10 false EPIM 0.458,3.469 0.771,3.625 0.313,0.156 10 false C40 1.031,4.344 1.344,4.5 0.313,0.156 10 false E2 2.333,4.344 2.708,4.563 0.375,0.219 10 false THIM 0.979,0.625 1.354,0.844 0.375,0.219 10 false THIM 1.115,0.979 1.49,1.198 0.375,0.219 10 false E2
*1 No. 3 Turbo Pressure Sensor
*2 ECM
*a Front view of wire harness connector
(to No. 3 Turbo Pressure Sensor)


Disconnect the No. 3 turbo pressure sensor connector.


b.

Connect terminals 4 (THIM) and 2 (E2) of the No. 3 turbo pressure sensor connector on the wire harness side.


c.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
50003 372 310
Standard value:

140°C (284°F)



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 3 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 3 turbo pressure sensor connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR