Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P012A15  Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit High Circuit Short to Battery or Open  P237415  Turbocharger/Supercharger Inlet Pressure Sensor "B" Circuit High Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P012A11.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P012A11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P012A15 Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit High Circuit Short to Battery or Open The output voltage from the No. 1 turbo pressure sensor (bank 1) is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 1 turbo pressure sensor (bank 1) circuit

·

No. 1 turbo pressure sensor (bank 1)

·

ECM


- SAE: P012D
P237415 Turbocharger/Supercharger Inlet Pressure Sensor "B" Circuit High Circuit Short to Battery or Open The output voltage from the No. 1 turbo pressure sensor (bank 2) is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 1 turbo pressure sensor (bank 2) circuit

·

No. 1 turbo pressure sensor (bank 2)

·

ECM


- SAE: P2377

HINT:

When a DTC is output, check the Data List item "Turbocharger/Supercharger Inlet Pressure Bank1 and Turbocharger/Supercharger Inlet Pressure Bank2" using the GTS.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Turbocharger/Supercharger Inlet Pressure Bank1 or Turbocharger/Supercharger Inlet Pressure Bank2 Malfunction
P012A15 120 kPa [17.4 psi] or higher
·

Short in VCPC circuit to PIC circuit

·

Open in PIC circuit

·

Open in EPIC circuit


P237415
·

Short in VPC2 circuit to PIC2 circuit

·

Open in PIC2 circuit

·

Open in EPC2 circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the air inlet duct internal pressure from the No. 1 turbo pressure sensor output voltage. If the No. 1 turbo pressure sensor output voltage is not within the normal range, there may be a malfunction in the No. 1 turbo pressure sensor or an open or short circuit. In this case, the ECM stores a DTC.

Example:

When the sensor output voltage is higher than 4.9 V for 3 seconds or more, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P012A15 or P237415.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P012A15 Bank 1
P237415 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C23,C38,C22)Location & Routing

Click Connector(C23)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly RH

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C22)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly LH

C23-2 (PIC) - C38-42 (PIC) Always Below 1 Ω
C23-1 (E2) - C38-45 (EPIC) Always Below 1 Ω
C22-2 (PIC2) - C38-41 (PIC2) Always Below 1 Ω
C22-1 (E22) - C38-43 (EPC2) Always Below 1 Ω
C23-2 (PIC) or C38-42 (PIC) - Other terminals Always 10 kΩ or higher
C22-2 (PIC2) or C38-41 (PIC2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR