Refer to DTC P024300.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P024300
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P024318 | Turbocharger/Supercharger Wastegate Actuator "A" Circuit Current Below Threshold | Either of the following conditions is met for 2 seconds or more (1 trip detection logic).
1.
All of the following conditions are met:
-
The battery voltage is 13.5 V or higher
-
The waste gate valve actuator (bank 1) drive duty cycle is 20% or higher
-
The waste gate valve actuator (bank 1) current is less than 0.5 A
2.
All of the following conditions are met:
-
The battery voltage is 10 V or higher, and below 13.5 V
-
The waste gate valve actuator (bank 1) drive duty cycle is 20% or higher
-
The waste gate valve actuator (bank 1) current is less than 0.2 A |
·
Open or short in waste gate valve actuator assembly (bank 1) circuit
·
Waste gate valve actuator assembly (turbocharger sub-assembly) (bank 1)
·
ECM |
- | SAE: P0245 |
| P024319 | Turbocharger/Supercharger Wastegate Actuator "A" Circuit Current Above Threshold | A motor driver IC high current limiter monitor input malfunction is detected for 1 second or more (1 trip detection logic). |
·
Open or short in waste gate valve actuator assembly (bank 1) circuit
·
Waste gate valve actuator assembly (turbocharger sub-assembly) (bank 1)
·
ECM |
- | SAE: P0246 |
| P024718 | Turbocharger/Supercharger Wastegate Actuator "B" Circuit Current Below Threshold | Either of the following conditions is met for 2 seconds or more (1 trip detection logic).
1.
All of the following conditions are met:
-
The battery voltage is 13.5 V or higher
-
The waste gate valve actuator (bank 2) drive duty cycle is 20% or higher
-
The waste gate valve actuator (bank 2) current is less than 0.5 A
2.
All of the following conditions are met:
-
The battery voltage is 10 V or higher, and below 13.5 V
-
The waste gate valve actuator (bank 2) drive duty cycle is 20% or higher
-
The waste gate valve actuator (bank 2) current is less than 0.2 A |
·
Open or short in waste gate valve actuator assembly (bank 2) circuit
·
Waste gate valve actuator assembly (turbocharger sub-assembly) (bank 2)
·
ECM |
- | SAE: P0249 |
| P024719 | Turbocharger/Supercharger Wastegate Actuator "B" Circuit Current Above Threshold | A motor driver IC high current limiter monitor input malfunction is detected for 1 second or more (1 trip detection logic). |
·
Open or short in waste gate valve actuator assembly (bank 2) circuit
·
Waste gate valve actuator assembly (turbocharger sub-assembly) (bank 2)
·
ECM |
- | SAE: P0250 |
The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the waste gate valve actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the waste gate valve actuator. In addition, if the waste gate valve does not operate properly (for example, it is stuck open), the ECM stores a DTC.
| Required Sensors/Components | Waste gate valve actuator assembly |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P024318, P024319, P024718 or P024719.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
| DTC | Suspected Area |
|---|---|
| P024318, P024319 | Bank 1 |
| P024718, P024719 | Bank 2 |
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
Perform "Inspection After Repair" after replacing the turbocharger sub-assembly.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
OK
NG
Disconnect the waste gate valve actuator assembly (turbocharger sub-assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C45,C37,C46)Location & Routingewd_type=routing;type=c,c,c;code=C45,C37,C46 |
||
| C45-2 (WG1+) - C37-1 (WGM+) | Always | Below 1 Ω |
| C45-1 (WG1-) - C37-2 (WGM-) | Always | Below 1 Ω |
| C46-1 (WG2+) - C37-20 (WG2+) | Always | Below 1 Ω |
| C46-2 (WG2-) - C37-21 (WG2-) | Always | Below 1 Ω |
| C45-2 (WG1+) or C37-1 (WGM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C45-1 (WG1-) or C37-2 (WGM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C46-1 (WG2+) or C37-20 (WG2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C46-2 (WG2-) or C37-21 (WG2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and wait 1 minute or more.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0024318, P024319, P024718 or P024719 is output | A |
| P0024318, P024319, P024718 or P024719 and other DTCs are output | B |
A
B