Refer to DTC P023A12.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P023A12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P026A00 | Charge Air Cooler Efficiency Below Threshold | Boost temperature is 85°C or more. When intake air flow rate is 30 gm/sec or more (2 trip detection logic). |
·
Lack of coolant (for intercooler)
·
Coolant leak (for intercooler)
·
Electric water pump assembly
·
No. 3 turbo pressure sensor (intake air temperature sensor)
·
Intercooler cooling radiator assembly
·
ECM |
- | SAE: P026A |
The ECM bases the detection on the signals from the intake air temperature sensor (No. 3 turbo pressure sensor). The ECM stores a DTC if the intake air temperature sensor value is outside the normal range.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher [A].
Enter the following menus: Powertrain / Engine / Data List / MAF Sensor Bank1 and MAF Sensor Bank2.
Drive the vehicle for at least 10 seconds at an intake air flow rate (total the values of MAF Sensor Bank1 and MAF Sensor Bank2) of 30 gm/sec or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive under load, such as up a slope or acceleration driving.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P026A00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform steps [B] and [C] again.
Refer to DTC P007A11.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P007A11
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P026A00 is output | A |
| P026A00 and other DTCs are output | B |
If any DTCs other than P026A00 are output, troubleshoot those DTCs first.
A
B
Remove the No. 3 turbo pressure sensor.
Do not disconnect the connector.
Read the value displayed on the GTS.
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
| Result | Proceed to |
|---|---|
| Other than the following | A |
| Difference between Intake Air Temperature B1S1 (Turbo) in the Data List and actual outside air temperature value is 10°C (18°F) or more. | B |
A
B
Check for deformation and blockage of the intercooler cooling radiator assembly.
Intercooler cooling radiator assembly does not have deformation or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to perform the inspection with the battery voltage at 11 V or more.
If the battery voltage is low, the electric water pump assembly may stop operating.
Read the Data List during 85% drive of the electric water pump.
| Active Test Display |
|---|
| Control the Intercooler Water Pump |
| Data List Display |
|---|
| Intercooler Water Pump Speed |
| GTS Operation | Electric Water Pump Speed | Proceed to |
|---|---|---|
| 85% | 4000 rpm or less | A |
| 7000 rpm or more | B | |
| Other than above | C |
A
B
C
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>COOLANT>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| At or below reservoir tank LOW level. | A |
| At or above reservoir tank LOW level. | B |
A
B
Check the turbocharger and intercooler cooling system for coolant leaks.
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>COOLANT>ON-VEHICLE INSPECTION
No leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| P026A00 is output | B |
A
B
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
Disconnect the No. 3 turbo pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C40,C38)Location & Routingewd_type=routing;type=c,c;code=C40,C38 |
||
| C40-4 (THIM) - C38-37 (THIM) | Always | Below 1 Ω |
| C40-2 (E2) - C38-39 (EPIM) | Always | Below 1 Ω |
| C40-4 (THIM) or C38-37 (THIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG