Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P003012  HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery  P003013  HO2S Heater Control Bank 1 Sensor 1 Circuit Open  P005012  HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery  P005013  HO2S Heater Control Bank 2 Sensor 1 Circuit Open  P101A9E  A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On  P103A9E  A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On  


DESCRIPTION

The air fuel ratio sensor (sensor 1) generates current that corresponds to the actual air fuel ratio. This sensor current is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor (sensor 1) malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor (sensor 1) is a planar type sensor and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

A485544E01
0.99,3.5 1.177,3.5 1.177,3.5 1.542,2.594 true 1.74,2.885 1.875,3.521 1.875,3.521 2.01,3.521 true 2.813,0.635 2.594,0.635 2.594,0.635 2.885,1.844 true 3.49,1.292 3.281,1.292 3.281,1.292 3.052,1.833 true 3.167,2.25 3.49,1.823 3.49,1.823 3.667,1.823 true 3.063,2.417 3.302,2.51 3.302,2.51 3.438,2.51 true 2.979,2.469 3.51,3.063 3.51,3.063 3.688,3.063 true 2.823,2.479 3.5,3.063 true 0.458,3.427 1.531,3.625 1.073,0.198 10 false Element 0.115,2.99 1.188,3.188 1.073,0.198 10 false Exhaust Gas 1.063,3.125 1.333,3.333 0.271,0.208 10 false A 1.969,3.146 2.24,3.354 0.271,0.208 10 false A 2.052,3.448 2.448,3.656 0.396,0.208 10 false Cover 2.885,0.563 4.021,1.052 1.135,0.49 10 false Solid Electrolyte (Zirconia Element) 3.573,1.229 4.188,1.448 0.615,0.219 10 false Alumina 3.708,1.75 4.323,1.969 0.615,0.219 10 false Heater 3.469,2.427 4.292,2.771 0.823,0.344 10 false Atmospheric Air 3.74,2.99 4.344,3.406 0.604,0.417 10 false Platinum Electrode 2.458,3.198 3.615,3.479 1.156,0.281 10 false A-A Cross Section 4.99,3 5.604,3.219 0.615,0.219 10 false 12 5.25,3 5.865,3.219 0.615,0.219 10 false 13 5.51,3 6.125,3.219 0.615,0.219 10 false 14 5.74,3 6.354,3.219 0.615,0.219 10 false 15 6.01,3 6.625,3.219 0.615,0.219 10 false 16 6.26,3 6.875,3.219 0.615,0.219 10 false 17 6.5,3 7.115,3.219 0.615,0.219 10 false 18 5.375,3.219 6.323,3.573 0.948,0.354 10 false Air Fuel Ratio 4.396,0.802 5.698,1.094 1.302,0.292 10 false Output Current (mA) 4.365,2.396 4.979,2.615 0.615,0.219 10 false -0.26 4.583,1.885 5.198,2.104 0.615,0.219 10 false 0 4.479,1.208 5.094,1.427 0.615,0.219 10 false 0.3

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor (sensor 1) heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor (sensor 1) heater circuit uses a relay on the +B side of the circuit.

A402951E60
0.125,0.115 3.573,0.458 3.448,0.344 10 false Reference (System Diagram of Sensor 1): 0.271,0.99 1.208,1.323 0.938,0.333 10 false from Battery 0.104,1.906 1.094,2.604 0.99,0.698 10 false from EFI MAIN NO. 1 Relay 2.625,1.156 3.396,1.583 0.771,0.427 10 false A/F NO. 1 3.438,1.906 4.781,2.417 1.344,0.51 10 false Air Fuel Ratio Sensor (Sensor 1) 3.854,0.677 4.625,1.115 0.771,0.438 10 false Heater 3.833,1.188 4.802,1.698 0.969,0.51 10 false Sensor 3.427,0.875 4.198,1.313 0.771,0.438 10 false +B 3.323,1.406 4.094,1.844 0.771,0.438 10 false A1A- 4.5,1.417 5.271,1.854 0.771,0.438 10 false A1A+ 5.052,1.417 5.823,1.854 0.771,0.438 10 false A1A+ 5.063,2.438 5.833,2.875 0.771,0.438 10 false A1A- 4.5,0.885 5.271,1.323 0.771,0.438 10 false HA1A 5.063,0.885 5.833,1.323 0.771,0.438 10 false HA1A 5.823,3.177 6.594,3.615 0.771,0.438 10 false ECM 6.177,1.521 6.979,2.021 0.802,0.5 10 false Duty Control 2.021,2.25 2.615,2.688 0.594,0.438 10 false A/F 1.323,1.177 1.917,1.615 0.594,0.438 10 false A/F



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003012 HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery The air fuel ratio sensor (bank 1 sensor 1) heater current is more than the specified value while the heater is operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P0032
P003013 HO2S Heater Control Bank 1 Sensor 1 Circuit Open The air fuel ratio sensor (bank 1 sensor 1) heater current is less than the specified value while the heater is operating (1 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0031
P005012 HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery The air fuel ratio sensor (bank 2 sensor 1) heater current is more than the specified value while the heater is operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P0052
P005013 HO2S Heater Control Bank 2 Sensor 1 Circuit Open The air fuel ratio sensor (bank 2 sensor 1) heater current is less than the specified value while the heater is operating (1 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0051
P101A9E A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On The air fuel ratio sensor (bank 1 sensor 1) heater voltage level is low while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on SAE: P101D
P103A9E A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On The air fuel ratio sensor (bank 2 sensor 1) heater voltage level is low while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on SAE: P103D

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor (sensor 1) to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor (sensor 1) detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor (sensor 1) is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful current signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor (sensor 1) becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor (sensor 1) heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0031 and P0051
Output duty cycle 7% or higher

P0032 and P0052
Output duty cycle 7% or higher

P101D and P103D
Output duty cycle Less than 75%

CONFIRMATION DRIVING PATTERN

A262623E64
0.792,0.969 1.583,1.26 0.792,0.292 10 false 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 false Idling 0.219,2.01 1.656,2.354 1.438,0.344 10 false Ignition Switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 false [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 false [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 false [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P003012, P003013, P005012, P005013, P101A9E or P103A9E.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [E] again.




WIRING DIAGRAM

A480011E01
0.677,2.771 1.396,2.99 0.719,0.219 10 false A/F 1.344,2.917 2.063,3.135 0.719,0.219 10 false A/F 2.854,4.083 4.198,4.531 1.344,0.448 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 2.854,3.896 3.167,4.104 0.313,0.208 10 false C29 1.813,2.792 2.5,3.177 0.688,0.385 10 false A/F NO. 1 1.917,2.375 2.792,2.604 0.875,0.229 10 false EFI-B NO. 4 2.094,1.573 3.177,1.771 1.083,0.198 10 false EFI MAIN NO. 1 0.406,1.417 1.49,1.615 1.083,0.198 10 false EFI MAIN NO. 1 1.5,1 2.219,1.219 0.719,0.219 10 false EFI NO. 2 2.792,6.531 4.156,6.896 1.365,0.365 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 2.792,6.344 3.396,6.5 0.604,0.156 10 false C30 0.448,4.594 1.49,4.823 1.042,0.229 10 false SUB R/B-NO. 1 0.656,6.875 1.24,7.073 0.583,0.198 10 false Battery 5.427,0.865 5.719,1.083 0.292,0.219 10 false B1 5.365,2.625 5.656,2.844 0.292,0.219 10 false C38 5.375,3.104 5.667,3.323 0.292,0.219 10 false C38 5.375,3.573 5.667,3.792 0.292,0.219 10 false C38 5.375,5.052 5.667,5.271 0.292,0.219 10 false C38 5.375,5.531 5.667,5.75 0.292,0.219 10 false C38 5.365,6 5.656,6.219 0.292,0.219 10 false C38 5.75,0.896 6.25,1.115 0.5,0.219 10 false MREL 5.75,2.51 6.25,2.729 0.5,0.219 10 false HA1A 5.74,2.99 6.24,3.208 0.5,0.219 10 false A1A+ 5.75,3.458 6.25,3.677 0.5,0.219 10 false A1A- 5.74,4.927 6.24,5.146 0.5,0.219 10 false HA2A 5.75,5.406 6.25,5.625 0.5,0.219 10 false A2A+ 5.75,5.885 6.25,6.104 0.5,0.219 10 false A2A- 6.104,7.146 6.604,7.365 0.5,0.219 10 false ECM 1.531,7.323 2.542,7.573 1.01,0.25 10 false *: Shielded 4.635,6.229 4.948,6.396 0.313,0.167 10 false * 4.635,3.813 4.948,3.979 0.313,0.167 10 false * 5.448,2.396 5.74,2.615 0.292,0.219 10 false 8 5.417,2.896 5.708,3.115 0.292,0.219 10 false 56 5.427,3.375 5.719,3.594 0.292,0.219 10 false 55 5.438,0.656 5.729,0.875 0.292,0.219 10 false 3 5.448,4.823 5.74,5.042 0.292,0.219 10 false 7 5.427,5.313 5.719,5.531 0.292,0.219 10 false 54 5.427,5.802 5.719,6.021 0.292,0.219 10 false 53 2.24,0.74 2.531,0.958 0.292,0.219 10 false 1 2.938,0.729 3.229,0.948 0.292,0.219 10 false 2 2.229,1.156 2.521,1.375 0.292,0.219 10 false 3 2.927,1.146 3.219,1.365 0.292,0.219 10 false 5 1.771,2.073 2.063,2.292 0.292,0.219 10 false 1 1.094,2.073 1.385,2.292 0.292,0.219 10 false 2 1.073,2.5 1.365,2.719 0.292,0.219 10 false 3 1.771,2.51 2.063,2.729 0.292,0.219 10 false 5 2.813,2.469 3.104,2.688 0.292,0.219 10 false 2 4.073,2.479 4.365,2.698 0.292,0.219 10 false 1 4.063,2.948 4.354,3.167 0.292,0.219 10 false 3 4.042,3.438 4.333,3.656 0.292,0.219 10 false 4 4.052,4.906 4.344,5.125 0.292,0.219 10 false 1 2.781,4.896 3.073,5.115 0.292,0.219 10 false 2 4.052,5.406 4.344,5.625 0.292,0.219 10 false 3 4.052,5.865 4.24,6.083 0.188,0.219 10 false 4 3.563,2.49 4.063,2.708 0.5,0.219 10 false HA1A 3.552,2.99 4.052,3.208 0.5,0.219 10 false A1A+ 3.594,3.458 4.094,3.677 0.5,0.219 10 false A1A- 3.01,2.469 3.271,2.688 0.26,0.219 10 false +B 3.021,4.885 3.281,5.104 0.26,0.219 10 false +B 3.563,4.938 4.063,5.156 0.5,0.219 10 false HA2A 3.573,5.417 4.073,5.635 0.5,0.219 10 false A2A+ 3.583,5.885 4.083,6.104 0.5,0.219 10 false A2A-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1 and A/F (O2) Sensor Heater Duty Ratio B2S1].

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor (sensor 1) output current (Click here Engine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P013616). If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P003012, P003013, P101A9E Bank 1
P005012, P005013, P103A9E Bank 2



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (SENSOR 1) (HEATER RESISTANCE)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

NG

REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

NG

6.INSPECT A/F RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C29,C38,C30)Location & Routing

Click Connector(C29)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C30)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

C29-1 (HA1A) - C38-8 (HA1A) Always Below 1 Ω
C30-1 (HA2A) - C38-7 (HA2A) Always Below 1 Ω
C29-1 (HA1A) or C38-8 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C30-1 (HA2A) or C38-7 (HA2A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P003012, P003013, P005012, P005013, P101A9E or P103A9E is output B




A

B

6.INSPECT A/F RELAY

OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)

NG

REPLACE A/F RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)
a.
A485543C01
0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 2.281,2.417 2.594,2.573 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 A/F Relay


Remove the A/F relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (A/F relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - A/F RELAY)

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - BODY GROUND)
a.

Remove the A/F relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (A/F relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR (SENSOR 1))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR (SENSOR 1))
a.

Remove the A/F relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the air fuel ratio sensor (sensor 1) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C29,C30)Location & Routing

Click Connector(C29)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C30)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

5 (A/F relay) - C29-2 (+B) Always Below 1 Ω
5 (A/F relay) - C30-2 (+B) Always Below 1 Ω
5 (A/F relay) or C29-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (A/F relay) or C30-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN NO. 1 RELAY - A/F RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR