Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P21CF13  Cylinder 1 Injector "B" Circuit Open  P21D013  Cylinder 2 Injector "B" Circuit Open  P21D113  Cylinder 3 Injector "B" Circuit Open  P21D213  Cylinder 4 Injector "B" Circuit Open  P21D313  Cylinder 5 Injector "B" Circuit Open  P21D413  Cylinder 6 Injector "B" Circuit Open  


DESCRIPTION

The D-4S system has two injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines the percentage of direct injection and port injection necessary in accordance with the engine speed and load.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P21CF13 Cylinder 1 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21CF
P21D013 Cylinder 2 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21D0
P21D113 Cylinder 3 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21D1
P21D213 Cylinder 4 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21D2
P21D313 Cylinder 5 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21D3
P21D413 Cylinder 6 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

IGT/INJ relay

·

ECM


Comes on SAE: P21D4

MONITOR DESCRIPTION

The ECM monitors the injection control of the port fuel injector assemblies. If a malfunction is detected in a port fuel injector assembly circuit, the ECM cancels the injection control for the corresponding cylinder, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Port fuel injector assembly (cylinder 1 to 6)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 3 minutes or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P21CF13, P21D013, P21D113, P21D213, P21D313 or P21D413.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A478985E02
2.708,0.719 5.708,0.917 3,0.198 10 false No. 1 Fuel Injector Assembly (for Port Injection) 2.719,0.542 2.948,0.729 0.229,0.188 10 false F1 1.073,0.51 1.354,0.698 0.281,0.188 10 false INJ 1.104,1.25 1.75,1.5 0.646,0.25 10 false IGT/INJ 0.354,4.24 0.917,4.792 0.563,0.552 10 false IGT/INJ 0.573,5.76 1.271,6.031 0.698,0.271 10 false Battery 0.396,5.094 1.49,5.354 1.094,0.26 10 false SUB R/B-NO. 1 2.708,1.354 3.063,1.552 0.354,0.198 10 false G1 2.708,1.521 5.708,1.719 3,0.198 10 false No. 2 Fuel Injector Assembly (for Port Injection) 2.719,2.188 2.948,2.375 0.229,0.188 10 false F2 2.719,2.354 5.719,2.552 3,0.198 10 false No. 3 Fuel Injector Assembly (for Port Injection) 2.74,3.042 3.094,3.229 0.354,0.188 10 false G2 2.729,3.208 5.729,3.406 3,0.198 10 false No. 4 Fuel Injector Assembly (for Port Injection) 2.729,4.01 5.729,4.208 3,0.198 10 false No. 5 Fuel Injector Assembly (for Port Injection) 2.75,3.844 2.979,4.031 0.229,0.188 10 false F3 2.74,4.677 3.063,4.865 0.323,0.188 10 false G3 2.708,4.844 5.708,5.042 3,0.198 10 false No. 6 Fuel Injector Assembly (for Port Injection) 5.427,0.375 5.729,0.552 0.302,0.177 10 false C37 5.438,1.198 5.823,1.385 0.385,0.188 10 false C37 5.438,2.031 5.792,2.229 0.354,0.198 10 false C37 5.438,2.854 5.854,3.073 0.417,0.219 10 false C37 5.438,3.688 5.885,3.896 0.448,0.208 10 false C37 5.438,4.51 5.854,4.719 0.417,0.208 10 false C37 5.469,5.833 5.813,6.031 0.344,0.198 10 false B1 5.479,0.177 5.75,0.354 0.271,0.177 10 false 51 5.469,1.01 5.74,1.188 0.271,0.177 10 false 50 5.479,1.833 5.75,2.01 0.271,0.177 10 false 49 5.469,2.656 5.74,2.833 0.271,0.177 10 false 48 5.479,3.49 5.75,3.667 0.271,0.177 10 false 47 5.479,4.323 5.75,4.5 0.271,0.177 10 false 46 5.479,5.646 5.75,5.823 0.271,0.177 10 false 35 6.208,6.292 6.604,6.5 0.396,0.208 10 false ECM 0.365,0.844 0.594,1.052 0.229,0.208 10 false 5 4.583,0.24 4.813,0.448 0.229,0.208 10 false 1 0.365,1.74 0.594,1.948 0.229,0.208 10 false 3 0.906,1.75 1.135,1.958 0.229,0.208 10 false 2 5.792,0.271 6.063,0.448 0.271,0.177 10 false #10 5.802,1.094 6.073,1.271 0.271,0.177 10 false #20 5.792,1.917 6.063,2.094 0.271,0.177 10 false #30 5.771,2.74 6.042,2.917 0.271,0.177 10 false #40 5.781,3.583 6.052,3.76 0.271,0.177 10 false #50 5.792,4.417 6.063,4.594 0.271,0.177 10 false #60 5.792,5.698 6.063,5.875 0.271,0.177 10 false E01 0.906,2.083 1.833,2.313 0.927,0.229 10 false EFI-B NO. 4 3.49,0.25 3.719,0.458 0.229,0.208 10 false 2 3.521,1.083 3.75,1.292 0.229,0.208 10 false 2 3.542,1.917 3.771,2.125 0.229,0.208 10 false 2 3.521,2.729 3.75,2.938 0.229,0.208 10 false 2 3.521,3.563 3.75,3.771 0.229,0.208 10 false 2 3.51,4.385 3.74,4.594 0.229,0.208 10 false 2 4.583,1.073 4.813,1.281 0.229,0.208 10 false 1 4.583,1.885 4.813,2.094 0.229,0.208 10 false 1 4.604,2.729 4.833,2.938 0.229,0.208 10 false 1 4.604,3.563 4.833,3.771 0.229,0.208 10 false 1 4.594,4.385 4.823,4.594 0.229,0.208 10 false 1 0.917,0.865 1.146,1.073 0.229,0.208 10 false 1 5.74,5.406 6.167,5.594 0.427,0.188 10 false MREL 5.469,5.406 5.813,5.604 0.344,0.198 10 false B1 5.51,5.208 5.781,5.385 0.271,0.177 10 false 3 1.656,2.76 2.271,3.146 0.615,0.385 10 false EFI MAIN NO. 1 0.938,4.156 1.552,4.542 0.615,0.385 10 false EFI MAIN NO. 1 1.479,3.573 2.208,3.813 0.729,0.24 10 false EFI NO. 2 1.448,2.458 1.677,2.667 0.229,0.208 10 false 2 1.458,3.323 1.688,3.531 0.229,0.208 10 false 1 0.906,3.323 1.135,3.531 0.229,0.208 10 false 3 0.906,2.448 1.135,2.656 0.229,0.208 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTCS OUTPUT (IN ADDITION TO DTC P21CF13, P21D013, P21D113, P21D213, P21D313 OR P21D413)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P21CF13, P21D013, P21D113, P21D213, P21D313 or P21D413 is output A
P21CF13, P21D013, P21D113, P21D213, P21D313 and P21D413 are output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - PORT FUEL INJECTOR ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)
a.

Disconnect the port fuel injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(F1,G1,F2,G2,F3,G3)Location & Routing

Click Connector(F1)Engine Compartment>No. 7 Engine Wire>No. 1 Fuel Injector Assembly (for Port Injection)

Click Connector(G1)Engine Compartment>No. 8 Engine Wire>No. 2 Fuel Injector Assembly (for Port Injection)

Click Connector(F2)Engine Compartment>No. 7 Engine Wire>No. 3 Fuel Injector Assembly (for Port Injection)

Click Connector(G2)Engine Compartment>No. 8 Engine Wire>No. 4 Fuel Injector Assembly (for Port Injection)

Click Connector(F3)Engine Compartment>No. 7 Engine Wire>No. 5 Fuel Injector Assembly (for Port Injection)

Click Connector(G3)Engine Compartment>No. 8 Engine Wire>No. 6 Fuel Injector Assembly (for Port Injection)

F1-2 - Body ground Ignition switch ON 11 to 14 V
G1-2 - Body ground Ignition switch ON 11 to 14 V
F2-2 - Body ground Ignition switch ON 11 to 14 V
G2-2 - Body ground Ignition switch ON 11 to 14 V
F3-2 - Body ground Ignition switch ON 11 to 14 V
G3-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - PORT FUEL INJECTOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the port fuel injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F1,C37,G1,F2,G2,F3,G3)Location & Routing

Click Connector(F1)Engine Compartment>No. 7 Engine Wire>No. 1 Fuel Injector Assembly (for Port Injection)

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(G1)Engine Compartment>No. 8 Engine Wire>No. 2 Fuel Injector Assembly (for Port Injection)

Click Connector(F2)Engine Compartment>No. 7 Engine Wire>No. 3 Fuel Injector Assembly (for Port Injection)

Click Connector(G2)Engine Compartment>No. 8 Engine Wire>No. 4 Fuel Injector Assembly (for Port Injection)

Click Connector(F3)Engine Compartment>No. 7 Engine Wire>No. 5 Fuel Injector Assembly (for Port Injection)

Click Connector(G3)Engine Compartment>No. 8 Engine Wire>No. 6 Fuel Injector Assembly (for Port Injection)

F1-1 - C37-51 (#10) Always Below 1 Ω
G1-1 - C37-50 (#20) Always Below 1 Ω
F2-1 - C37-49 (#30) Always Below 1 Ω
G2-1 - C37-48 (#40) Always Below 1 Ω
F3-1 - C37-47 (#50) Always Below 1 Ω
G3-1 - C37-46 (#60) Always Below 1 Ω
F1-1 or C37-51 (#10) - Body ground and other terminals Always 10 kΩ or higher
G1-1 or C37-50 (#20) - Body ground and other terminals Always 10 kΩ or higher
F2-1 or C37-49 (#30) - Body ground and other terminals Always 10 kΩ or higher
G2-1 or C37-48 (#40) - Body ground and other terminals Always 10 kΩ or higher
F3-1 or C37-47 (#50) - Body ground and other terminals Always 10 kΩ or higher
G3-1 or C37-46 (#60) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)

Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL INJECTOR (for Port Injection)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - PORT FUEL INJECTOR ASSEMBLY)
a.

Remove the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the port fuel injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F1,G1,F2,G2,F3,G3)Location & Routing

Click Connector(F1)Engine Compartment>No. 7 Engine Wire>No. 1 Fuel Injector Assembly (for Port Injection)

Click Connector(G1)Engine Compartment>No. 8 Engine Wire>No. 2 Fuel Injector Assembly (for Port Injection)

Click Connector(F2)Engine Compartment>No. 7 Engine Wire>No. 3 Fuel Injector Assembly (for Port Injection)

Click Connector(G2)Engine Compartment>No. 8 Engine Wire>No. 4 Fuel Injector Assembly (for Port Injection)

Click Connector(F3)Engine Compartment>No. 7 Engine Wire>No. 5 Fuel Injector Assembly (for Port Injection)

Click Connector(G3)Engine Compartment>No. 8 Engine Wire>No. 6 Fuel Injector Assembly (for Port Injection)

5 (IGT/INJ relay) - F1-2 Always Below 1 Ω
5 (IGT/INJ relay) - G1-2 Always Below 1 Ω
5 (IGT/INJ relay) - F2-2 Always Below 1 Ω
5 (IGT/INJ relay) - G2-2 Always Below 1 Ω
5 (IGT/INJ relay) - F3-2 Always Below 1 Ω
5 (IGT/INJ relay) - G3-2 Always Below 1 Ω
5 (IGT/INJ relay) or F1-2 - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or G1-2 - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or F2-2 - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or G2-2 - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or F3-2 - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or G3-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT IGT/INJ RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IGT/INJ RELAY

OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF IGT/INJ RELAY)

NG

REPLACE IGT/INJ RELAY

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF IGT/INJ RELAY)
a.
A485843C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 0.313,1.313 0.625,1.469 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 IGT/INJ Relay


Remove the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGT/INJ relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGT/INJ RELAY)

8.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - BODY GROUND)
a.

Remove the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IGT/INJ relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN NO. 1 RELAY - IGT/INJ RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR