Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM J

V35A-FTS ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A485826E01
6.021,0.542 6.406,0.781 0.385,0.24 10 false IGT1 6.021,1.813 6.406,2.052 0.385,0.24 10 false IGT3 6.01,3.052 6.396,3.292 0.385,0.24 10 false IGT5 6.01,4.313 6.396,4.552 0.385,0.24 10 false IGT2 6.01,5.573 6.396,5.813 0.385,0.24 10 false IGT4 6.01,6.802 6.396,7.042 0.385,0.24 10 false IGT6 3.646,1.104 4.031,1.344 0.385,0.24 10 false C1 3.667,1.271 5.677,1.563 2.01,0.292 10 false No. 1 Ignition Coil Assembly 4.688,0.688 5.073,0.927 0.385,0.24 10 false IGT1 4.688,1.948 5.073,2.188 0.385,0.24 10 false IGT3 4.698,3.198 5.083,3.438 0.385,0.24 10 false IGT5 4.698,4.448 5.083,4.688 0.385,0.24 10 false IGT2 4.698,5.708 5.083,5.948 0.385,0.24 10 false IGT4 4.698,6.958 5.083,7.198 0.385,0.24 10 false IGT6 4.125,0.521 4.51,0.76 0.385,0.24 10 false +B 4.073,1.75 4.458,1.99 0.385,0.24 10 false +B 4.083,3.021 4.469,3.26 0.385,0.24 10 false +B 4.104,4.271 4.49,4.51 0.385,0.24 10 false +B 4.083,5.552 4.469,5.792 0.385,0.24 10 false +B 4.083,6.802 4.469,7.042 0.385,0.24 10 false +B 4.094,0.906 4.479,1.146 0.385,0.24 10 false GND 4.073,2.156 4.458,2.396 0.385,0.24 10 false GND 4.083,3.417 4.469,3.656 0.385,0.24 10 false GND 4.083,4.656 4.469,4.896 0.385,0.24 10 false GND 4.083,5.906 4.469,6.146 0.385,0.24 10 false GND 4.083,7.177 4.469,7.417 0.385,0.24 10 false GND 5.719,0.469 5.927,0.729 0.208,0.26 10 false 61 5.729,1.74 5.938,2 0.208,0.26 10 false 59 5.729,3 5.938,3.26 0.208,0.26 10 false 57 5.719,4.26 5.927,4.521 0.208,0.26 10 false 60 5.708,5.521 5.917,5.781 0.208,0.26 10 false 58 5.719,6.75 5.927,7.01 0.208,0.26 10 false 56 5.677,6.958 6.063,7.198 0.385,0.24 10 false C37 6.302,8.229 6.688,8.469 0.385,0.24 10 false ECM 5.083,0.573 5.292,0.833 0.208,0.26 10 false 2 3.885,0.406 4.094,0.667 0.208,0.26 10 false 1 3.875,0.781 4.083,1.042 0.208,0.26 10 false 3 5.073,1.823 5.281,2.083 0.208,0.26 10 false 2 5.083,3.083 5.292,3.344 0.208,0.26 10 false 2 5.083,4.344 5.292,4.604 0.208,0.26 10 false 2 5.073,5.573 5.281,5.833 0.208,0.26 10 false 2 5.083,6.833 5.292,7.094 0.208,0.26 10 false 2 3.885,1.635 4.094,1.896 0.208,0.26 10 false 1 3.885,2.885 4.094,3.146 0.208,0.26 10 false 1 3.875,4.156 4.083,4.417 0.208,0.26 10 false 1 3.875,5.417 4.083,5.677 0.208,0.26 10 false 1 3.885,6.667 4.094,6.927 0.208,0.26 10 false 1 3.896,2.042 4.104,2.302 0.208,0.26 10 false 3 3.896,3.292 4.104,3.552 0.208,0.26 10 false 3 3.885,4.552 4.094,4.813 0.208,0.26 10 false 3 3.875,5.802 4.083,6.063 0.208,0.26 10 false 3 3.875,7.052 4.083,7.313 0.208,0.26 10 false 3 3.708,2.323 4.094,2.563 0.385,0.24 10 false C3 3.729,2.5 5.74,2.792 2.01,0.292 10 false No. 3 Ignition Coil Assembly 3.729,3.802 5.74,4.094 2.01,0.292 10 false No. 5 Ignition Coil Assembly 3.719,3.635 4.104,3.875 0.385,0.24 10 false C5 3.646,5.01 5.656,5.302 2.01,0.292 10 false No. 2 Ignition Coil Assembly 3.646,4.854 4.031,5.094 0.385,0.24 10 false C2 3.656,6.292 5.667,6.583 2.01,0.292 10 false No. 4 Ignition Coil Assembly 3.646,6.125 4.031,6.365 0.385,0.24 10 false C4 3.625,7.521 5.635,7.813 2.01,0.292 10 false No. 6 Ignition Coil Assembly 3.625,7.344 4.01,7.583 0.385,0.24 10 false C6 0.531,0.646 0.917,0.885 0.385,0.24 10 false IGN 1.375,1.5 1.948,1.75 0.573,0.25 10 false IGT/INJ 0.458,6 1.094,6.438 0.635,0.438 10 false IGT/INJ 1.854,4.531 2.542,4.948 0.688,0.417 10 false EFI MAIN NO. 1 0.49,6.875 1.635,7.146 1.146,0.271 10 false SUB R/B-NO. 1 0.656,7.604 1.448,7.844 0.792,0.24 10 false Battery 0.448,1.979 0.656,2.24 0.208,0.26 10 false 3 0.458,1.031 0.667,1.292 0.208,0.26 10 false 5 1.104,1.99 1.313,2.25 0.208,0.26 10 false 2 1.104,1.042 1.313,1.302 0.208,0.26 10 false 1 5.719,7.875 6.104,8.115 0.385,0.24 10 false B1 5.76,7.688 5.969,7.948 0.208,0.26 10 false 3 6.01,7.865 6.49,8.094 0.479,0.229 10 false MREL 5.677,5.698 6.073,5.948 0.396,0.25 10 false C37 5.677,4.458 6.073,4.708 0.396,0.25 10 false C37 5.677,3.198 6.073,3.448 0.396,0.25 10 false C37 5.677,1.948 6.073,2.198 0.396,0.25 10 false C37 5.677,0.688 6.073,0.938 0.396,0.25 10 false C37 1.135,5.906 1.823,6.323 0.688,0.417 10 false EFI MAIN NO. 1 1.146,3.823 2.031,4.104 0.885,0.281 10 false EFI-B NO. 4 1.688,5.292 2.573,5.573 0.885,0.281 10 false EFI NO. 2 1.646,4.198 1.854,4.458 0.208,0.26 10 false 2 1.646,5.083 1.854,5.344 0.208,0.26 10 false 1 1.104,4.198 1.313,4.458 0.208,0.26 10 false 5 1.104,5.073 1.313,5.333 0.208,0.26 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test first. If none of the cylinders spark, or if only some cylinders do not spark, check this circuit to determine if the ignition coil and spark plug are normal.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C1,C2,C3,C4,C5,C6)Location & Routing

Click Connector(C1)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C2)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C3)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C4)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C5)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C6)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C1-1 (+B) - C1-3 (GND) Ignition switch ON 11 to 14 V
C2-1 (+B) - C2-3 (GND) Ignition switch ON 11 to 14 V
C3-1 (+B) - C3-3 (GND) Ignition switch ON 11 to 14 V
C4-1 (+B) - C4-3 (GND) Ignition switch ON 11 to 14 V
C5-1 (+B) - C5-3 (GND) Ignition switch ON 11 to 14 V
C6-1 (+B) - C6-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C1,C37,C2,C3,C4,C5,C6)Location & Routing

Click Connector(C1)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C2)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C3)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C4)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C5)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C6)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C1-2 (IGT1) - C37-61 (IGT1) Always Below 1 Ω
C2-2 (IGT2) - C37-60 (IGT2) Always Below 1 Ω
C3-2 (IGT3) - C37-59 (IGT3) Always Below 1 Ω
C4-2 (IGT4) - C37-58 (IGT4) Always Below 1 Ω
C5-2 (IGT5) - C37-57 (IGT5) Always Below 1 Ω
C6-2 (IGT6) - C37-56 (IGT6) Always Below 1 Ω
C1-2 (IGT1) or C37-61 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C2-2 (IGT2) or C37-60 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C3-2 (IGT3) or C37-59 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C4-2 (IGT4) or C37-58 (IGT4) - Body ground and other terminals Always 10 kΩ or higher
C5-2 (IGT5) or C37-57 (IGT5) - Body ground and other terminals Always 10 kΩ or higher
C6-2 (IGT6) or C37-56 (IGT6) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C1,C2,C3,C4,C5,C6)Location & Routing

Click Connector(C1)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C2)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C3)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C4)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C5)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C6)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

C1-3 (GND) - Body ground Always Below 1 Ω
C2-3 (GND) - Body ground Always Below 1 Ω
C3-3 (GND) - Body ground Always Below 1 Ω
C4-3 (GND) - Body ground Always Below 1 Ω
C5-3 (GND) - Body ground Always Below 1 Ω
C6-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - IGNITION COIL ASSEMBLY)
a.

Disconnect the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C1,C2,C3,C4,C5,C6)Location & Routing

Click Connector(C1)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 1

Click Connector(C2)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 2

Click Connector(C3)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 3

Click Connector(C4)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 4

Click Connector(C5)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 5

Click Connector(C6)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Ignition Coil Assembly No. 6

5 (IGT/INJ relay) - C1-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) - C2-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) - C3-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) - C4-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) - C5-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) - C6-1 (+B) Always Below 1 Ω
5 (IGT/INJ relay) or C1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or C2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or C3-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or C4-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or C5-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGT/INJ relay) or C6-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT IGT/INJ RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT IGT/INJ RELAY

OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF IGT/INJ RELAY)

NG

REPLACE IGT/INJ RELAY

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF IGT/INJ RELAY)
a.
A485843C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 0.313,1.313 0.625,1.469 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 IGT/INJ Relay


Remove the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (IGT/INJ relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGT/INJ RELAY)

7.CHECK HARNESS AND CONNECTOR (IGT/INJ RELAY - BODY GROUND)
a.

Remove the IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (IGT/INJ relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 1 RELAY - IGT/INJ RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 1 RELAY - IGT/INJ RELAY)
a.

Remove the EFI MAIN NO. 1 relay and IGT/INJ relay from the No. 2 engine room relay block and junction block assembly.


b.

Remove the A/F relay, EFI MAIN NO. 2 relay and EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.

HINT:

Remove the A/F relay, EFI MAIN NO. 2 relay and EFI MAIN NO. 3 connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI MAIN NO. 1 relay) - 1 (IGT/INJ relay) Always Below 1 Ω
5 (EFI MAIN NO. 1 relay) or 1 (IGT/INJ relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR