Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P003312  Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery  P00C012  Turbocharger/Supercharger Bypass Valve "B" Control Circuit Short to Battery  


DESCRIPTION

The air by-pass valve assembly is installed in the air outlet duct. It opens and closes in response to drive commands from the ECM. During normal boosting, the air by-pass valve assembly is closed, and when the throttle valve is closed while the boost pressure is applied, the air by-pass valve assembly opens and the excess pressure between the turbocharger and throttle valve is released to prevent the surge phenomenon*.

*: This phenomenon is when the intake air flow reverses. As a result, an abnormal noise is easily generated during deceleration.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery Short circuit in air by-pass valve assembly (bank 1) circuit and power supply circuit (1 trip detection logic).
·

Short in air by-pass valve assembly (bank 1) circuit

·

Air by-pass valve assembly (bank 1)

·

ECM


- SAE: P0035
P00C012 Turbocharger/Supercharger Bypass Valve "B" Control Circuit Short to Battery Short circuit in air by-pass valve assembly (bank 2) circuit and power supply circuit (1 trip detection logic).
·

Short in air by-pass valve assembly (bank 2) circuit

·

Air by-pass valve assembly (bank 2)

·

ECM


- SAE: P00C2

MONITOR DESCRIPTION

The ECM monitors the output voltage while the air by-pass valve assembly is operating.

The air by-pass valve assembly turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the air by-pass valve assembly circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

A330723E39
4.448,0.958 4.802,0.667 4.802,0.667 5.021,0.667 false 3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.396,2.365 1.313,2.75 0.917,0.385 10 false Ignition Switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [D] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 5.083,0.604 6.031,0.792 0.948,0.188 10 false Released 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.125,1.417 3.604,1.615 0.479,0.198 10 false [B] 4.906,1.406 5.365,1.604 0.458,0.198 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Quickly release the accelerator pedal from the fully depressed position [C].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P003312 or P00C012.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [B] through [D] again.




WIRING DIAGRAM

A408332E02
0.51,3.573 1.188,3.823 0.677,0.25 10 false Battery 0.323,2.271 1.49,2.542 1.167,0.271 10 false SUB R/B-NO. 1 0.333,1.656 1.438,1.854 1.104,0.198 10 false EFI MAIN NO. 3 2.896,1.875 4.01,2.24 1.115,0.365 10 false EFI MAIN NO. 3 3.698,1.667 4.375,1.917 0.677,0.25 10 false EFI NO. 3 2.396,1.083 3.198,1.323 0.802,0.24 10 false EFI-B NO. 4 1.094,0.51 1.792,0.719 0.698,0.208 10 false EFI NO. 2 0.313,1.083 1.406,1.365 1.094,0.281 10 false EFI MAIN NO. 1 1.635,1.302 2.719,1.583 1.083,0.281 10 false EFI MAIN NO. 1 4.469,1.792 5.646,2.052 1.177,0.26 10 false C41 4.469,1.958 6.26,2.302 1.792,0.344 10 false Air By-pass Valve Assembly (Bank 1) 4.448,3.156 5.625,3.417 1.177,0.26 10 false C42 4.438,3.313 6.24,3.667 1.802,0.354 10 false Air By-pass Valve Assembly (Bank 2) 6.427,2.74 6.979,2.958 0.552,0.219 10 false ABV2 6.427,1.385 6.979,1.604 0.552,0.219 10 false ABV 6.573,4.344 7.125,4.563 0.552,0.219 10 false ECM 6.417,0.375 6.969,0.594 0.552,0.219 10 false MREL 6.083,0.365 6.469,0.635 0.385,0.271 10 false B1 6.063,1.5 6.417,1.729 0.354,0.229 10 false C37 6.063,2.854 6.406,3.104 0.344,0.25 10 false C37 6.104,3.99 6.458,4.198 0.354,0.208 10 false B1 6.125,0.156 6.51,0.427 0.385,0.271 10 false 3 6.104,1.302 6.49,1.573 0.385,0.271 10 false 30 6.104,2.667 6.49,2.938 0.385,0.271 10 false 29 6.146,3.802 6.354,4.063 0.208,0.26 10 false 9 6.427,3.99 6.635,4.25 0.208,0.26 10 false E1 2.427,0.813 2.604,1.042 0.177,0.229 10 false 5 3.708,1.365 3.885,1.594 0.177,0.229 10 false 5 3.688,0.813 3.865,1.042 0.177,0.229 10 false 1 2.417,0.26 2.594,0.49 0.177,0.229 10 false 2 1.729,0.26 1.906,0.49 0.177,0.229 10 false 1 1.74,0.823 1.917,1.052 0.177,0.229 10 false 3 3.01,0.802 3.188,1.031 0.177,0.229 10 false 2 3.01,1.365 3.188,1.594 0.177,0.229 10 false 3 4.75,1.375 4.927,1.604 0.177,0.229 10 false 2 4.76,2.74 4.938,2.969 0.177,0.229 10 false 2 5.771,1.365 5.948,1.594 0.177,0.229 10 false 1 5.771,2.719 5.948,2.948 0.177,0.229 10 false 1 5.375,1.375 5.927,1.594 0.552,0.219 10 false ABV 4.958,1.365 5.24,1.594 0.281,0.229 10 false +B 4.958,2.74 5.24,2.969 0.281,0.229 10 false +B 5.302,2.729 5.698,2.958 0.396,0.229 10 false ABV2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P003312 Bank 1
P00C012 Bank 2



PROCEDURE

1.INSPECT AIR BY-PASS VALVE ASSEMBLY

OK

2.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)

OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312 OR P00C012)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312 OR P00C012)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P003312 or P00C012.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P003312 or P00C012 is output)
B




A

B