Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PANORAMIC VIEW MONITOR DIAGNOSIS SYSTEM


a.

For panoramic view monitor system diagnosis, signals received by the parking assist ECU can be checked, and the panoramic view monitor system can be calibrated, adjusted and checked using the multi-display assembly.

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (VIEW ADJUSTMENT)


E461511E01
2.76,1 5.969,1.198 3.208,0.198 10 false Start diagnostic mode 0.167,0.125 1.167,0.49 1,0.365 12 false Example


DIAGNOSIS SCREEN TRANSITION (STEERING ANGLE SETTING)


E461512E01
2.76,0.979 5.969,1.177 3.208,0.198 10 false Start diagnostic mode 5.51,5.167 5.823,5.365 0.313,0.198 10 false or 0.219,0.094 1.333,0.396 1.115,0.302 12 false Example


DIAGNOSIS SCREEN TRANSITION (BACK CAMERA SETTING)


E467662E01
2.76,0.99 5.969,1.188 3.208,0.198 10 false Start diagnostic mode 0.229,0.167 1.385,0.646 1.156,0.479 12 false Example

E372772


DIAGNOSIS SCREEN TRANSITION (CAMERA CHECK)


E467663E01
2.76,0.99 5.969,1.188 3.208,0.198 10 false Start diagnostic mode 0.188,0.177 1.167,0.521 0.979,0.344 12 false Example


DIAGNOSIS SCREEN TRANSITION (DIAG CHECK)


E467664E01
2.771,0.99 5.979,1.188 3.208,0.198 10 false Start diagnostic mode 0.26,0.156 1.49,0.552 1.229,0.396 12 false Example



DIAG CHECK


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.



iii.
E467665

Select "Diag Check" on the "Mode Setting (*)" screen to display the "Diag Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Check Diagnosis

i.

On the "Diag Check (*)" screen, DTCs output when the parking assist ECU detects a malfunction can be checked.

E439845

Indication Name Measurement Item Note
Diag Code DTC DTCs output when the parking assist ECU detects a malfunction
RoB Code RoB Code RoB output when the parking assist ECU detects a malfunction
DID DID table Values based on information displayed on Data List





SIGNAL CHECK (PARKING ASSIST ECU INPUT SIGNAL)


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen



iii.
E467665

When the screen changes to the "Mode Setting (*)" screen, select "View Adjustment" to display the "Signal Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Signal check

i.
E382500

On the "Signal Check (*)" screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.

Item Inspection Detail Note
CAN Speed signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW Panoramic view monitor switch (trip switch)

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.



d.

CAMERA SW inspection

i.

Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".

HINT:

If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to the Problem Symptoms Table ("CHK" message(s) are displayed on the "Signal Check" screen).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.






CAMERA CHECK


HINT:
·

Use this function when symptoms such as the camera images not being displayed occur.

·

On the DTC screen, the 4 camera images are displayed as one image and the images input to the parking assist ECU from the cameras can be checked.



a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen



iii.
E467665

When the screen changes to the "Mode Setting (*)" screen, select "Camera Check" to display the "Camera Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.

Check camera images.

i.
E376965

On the "Camera Check (*)" screen, the images that are input to the parking assist ECU from the 4 cameras are displayed on the screen and the camera images can be checked.

Indication Name Measurement Item Indication Name Measurement Item
Front Front television camera assembly Back Rear television camera assembly
Left Side television camera assembly LH Right Side television camera assembly RH





CAMERA DETECTION SETTING


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options.

Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.


i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the power switch off and enter the diagnosis screen after turning the power switch on (IG) once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed "Signal Check (*)" screen
Performed "Mode Setting (*)" screen




b.

Camera Detection Setting.

i.
E467665

Select "Camera Detection Setting" on the "Mode Setting (*)" screen.


ii.
E366791

Select ON or OFF on the "Camera Detection Setting (*)" screen as necessary.

HINT:

After selecting ON or OFF, return to the "Mode Setting (*)" screen by selecting "OK" or "Back".






CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION