Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch (trip switch) DTC is not output Panoramic view monitor switch (trip switch)

WIRING DIAGRAM

E287159E34
0.979,2.25 4.646,2.448 3.667,0.198 10 false : CAN Communication Line 2.844,0.406 3.167,0.625 0.323,0.219 10 false ECU 3.25,0.396 3.406,0.594 0.156,0.198 10 false 6 4.844,0.406 5.135,0.604 0.292,0.198 10 false 15 5.146,0.51 5.656,0.688 0.51,0.177 10 false BLSW 1.635,0.802 2.146,0.979 0.51,0.177 10 false I80 1.635,1 3.594,1.333 1.958,0.333 10 false Panoramic View Monitor Switch (Trip Switch) 5.104,2.156 5.469,2.354 0.365,0.198 10 false I60 5.115,2.344 6.542,2.573 1.427,0.229 10 false Parking Assist ECU 1.854,0.406 2.01,0.604 0.156,0.198 10 false 3 2.094,0.406 2.25,0.604 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E382500

Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH (TRIP SWITCH) - PARKING ASSIST ECU AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH (TRIP SWITCH) - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the I80 panoramic view monitor switch (trip switch) connector.


b.

Disconnect the I60 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I60,I80)Location & Routing

Click Connector(I60)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

Click Connector(I80)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Trip Switch

I60-15 (BLSW) - I80-6 (ECU) Always Below 1 Ω
I80-3 (E) - Body ground Always Below 1 Ω
I60-15 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH (TRIP SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR