Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P253314  Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

When the ignition switch is turned to ON, the battery power source is supplied to the IGP and IGR terminals of the ECM. When the ignition switch is off, the battery power source is cut off.

When the ignition switch is turned off during driving, the battery power source supplied to the IGP terminal is cut off. However, the battery power source supplied to the IGR terminal is supplied until the vehicle is stopped and the ignition switch is turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P253314 Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open Short to ground or open in IGR terminal circuit (2 trip detection logic).
·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector

·

ECM


Does not come on SAE: P2534

MONITOR DESCRIPTION

The ECM stores a DTC when there is no battery voltage to the IGR terminal even though there is battery voltage to the IGP terminal.

WIRING DIAGRAM

A488864E01
0.542,4.646 1.177,4.875 0.635,0.229 10 false Battery 3.271,2.333 3.729,2.573 0.458,0.24 10 false I40 6.375,4.635 6.833,4.875 0.458,0.24 10 false ECM 4.271,3.76 5.344,4 1.073,0.24 10 false ENG-IGP NO.1 3.667,3.458 4.125,3.698 0.458,0.24 10 false 5 0.646,3.771 1.677,4.042 1.031,0.271 10 false SUB R/B-NO.1 5.75,4.104 6.208,4.344 0.458,0.24 10 false C92 6.125,4.104 6.583,4.344 0.458,0.24 10 false E1 5.792,3.896 6.167,4.083 0.375,0.188 10 false 81 5.781,3.604 6.115,3.813 0.333,0.208 10 false B2 5.792,0.656 6.125,0.865 0.333,0.208 10 false B2 5.823,3.375 6.094,3.573 0.271,0.198 10 false 4 5.792,0.438 6.167,0.625 0.375,0.188 10 false 34 6.125,3.604 6.583,3.844 0.458,0.24 10 false IGP 6.125,0.646 6.583,0.885 0.458,0.24 10 false IGR 3,4.344 3.76,4.552 0.76,0.208 10 false IGP NO.2 1,2.688 1.76,2.896 0.76,0.208 10 false IGP NO.1 2.823,3.458 3.281,3.698 0.458,0.24 10 false 3 3.667,3.896 4.125,4.135 0.458,0.24 10 false 2 2.823,3.896 3.281,4.135 0.458,0.24 10 false 1 1.979,4.188 3.052,4.427 1.073,0.24 10 false ECU-IGP NO.3 1.76,3.115 2.219,3.354 0.458,0.24 10 false 5 2.385,3.115 2.844,3.354 0.458,0.24 10 false 2 1.76,2.26 2.219,2.5 0.458,0.24 10 false 3 2.375,2.271 2.833,2.51 0.458,0.24 10 false 1 4.083,1.969 4.844,2.177 0.76,0.208 10 false IGPD 4.063,1.146 4.823,1.354 0.76,0.208 10 false IGRD 3.271,2.5 6.01,2.813 2.74,0.313 10 false Certification ECU (smart key ECU assembly) 3.792,1.823 4.167,2.01 0.375,0.188 10 false 24 3.792,1.042 4.167,1.229 0.375,0.188 10 false 11 0.927,1.479 1.688,1.688 0.76,0.208 10 false IGR NO.3 0.781,1.042 1.24,1.281 0.458,0.24 10 false 2 1.583,1.031 2.042,1.271 0.458,0.24 10 false 1 0.781,0.552 1.24,0.792 0.458,0.24 10 false 3 1.594,0.552 2.052,0.792 0.458,0.24 10 false 5 2.271,0.813 3.344,1.052 1.073,0.24 10 false ENG-IGR NO.1

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 1 minute or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P253314

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system is malfunctioning.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (IGR)
a.

Read the Data List.

Powertrain > Engine > Data List
Tester Display
IGR
50003 372 1232
Result:
Result Proceed to
The value of IGR is ON A
None of the above conditions are met B




A

B

2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
2.CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B2-34 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT RELAY (IGR NO.3)
3.INSPECT RELAY (IGR NO.3)
a.

Inspect the relay (IGR NO.3).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - ECM)

NG

REPLACE RELAY (IGR NO.3)

4.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - ECM)
a.

Remove the relay (IGR NO.3).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

5 (IGR NO.3 relay) - B2-34 (IGR) Always Below 1 Ω
5 (IGR NO.3 relay) or B2-34 (IGR) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - BODY GROUND)
a.

Remove the relay (IGR NO.3).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGR NO.3 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RELAY (IGR NO.3) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Remove the relay (IGR NO.3).


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

1 (IGR NO.3 relay) - I40-11 (IGRD) Always Below 1 Ω
1 (IGR NO.3 relay) or I40-11 (IGRD) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR