Home › General › MAINTENANCE › 1GR-FE COOLANT
RM38G0E _V1 General _100461 MAINTENANCE _0470531 1GR-FE COOLANT A

MAINTENANCE  1GR-FE COOLANT  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·
A487150

Do not remove the reserve tank cap, radiator cap sub-assembly, radiator drain cock plug or cylinder block water drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A343690

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51420 2.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 3.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the reserve tank cap, radiator cap sub-assembly, radiator drain cock plug or cylinder block water drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A487157

Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.
A487158

Connect a hose with an inside diameter of 8 mm (0.315 in.) to the cylinder block water drain cock plug as shown in the illustration.


c.

Loosen the radiator drain cock plug.

A487159C01
0.979,3.896 0.979,3.646 0.979,3.646 1.479,3.646 true 6.167,1.938 6.167,1.188 true 0.917,3.948 1.135,4.156 0.219,0.208 10 false *1 6.115,1.969 6.333,2.177 0.219,0.208 10 false *2
*1 Radiator Drain Cock Plug *2 Cylinder Block Water Drain Cock Plug



d.

Remove the radiator cap sub-assembly. Then drain the coolant.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.



e.

Loosen the cylinder block water drain cock plug.


f.

Tighten the cylinder block water drain cock plug.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


g.

Tighten the radiator drain cock plug by hand.


h.

Disconnect the hose from the cylinder block water drain cock plug.


i.

Disconnect the hose from the radiator drain cock.


Hide 4.ADD ENGINE COOLANT

CAUTION:
·

Do not remove the reserve tank cap, radiator cap sub-assembly, radiator drain cock plug or cylinder block water drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·

To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and cooling fans when working in the engine compartment with the engine running.



a.

Remove the reserve tank cap.


b.

Add engine coolant.

Standard Capacity:
Item Specified Condition
w/o Rear Air Conditioning system 11.6 liters (12.3 US qts, 10.2 Imp. qts)
w/ Rear Air Conditioning system 13.8 liters (14.6 US qts, 12.1 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).



c.

Slowly pour coolant into the radiator reserve tank assembly until it reaches the Full line.


d.

Install the reserve tank cap.


e.

Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.


f.

Install the radiator cap sub-assembly.


g.

Set the air conditioning as follows while warming up the engine.

Item Condition
Fan speed Any setting except off
Temperature Toward WARM
Air conditioning switch Off


h.

Start the engine and warm it up until the thermostat opens.

HINT:

The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



i.

Maintain the engine speed at 2000 to 2500 rpm.

NOTICE:
·

Immediately after starting the engine, if the radiator reserve tank assembly does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.

·

Make sure that the radiator reserve tank assembly still has some coolant in it.

·

Pay attention to the needle of the coolant temperature meter. Make sure that the needle does not show an abnormally high temperature.

·

If there is not enough coolant, the engine may burn out or overheat.




j.

Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

CAUTION:
·

Wear protective gloves. Hot areas of the parts may injure your hands.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the fan.




k.

Stop the engine and wait until the engine coolant cools down to ambient temperature.

CAUTION:

Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



l.

Check that the coolant level is between the Full and Low lines.

If the coolant level is below the Low line, repeat all of the procedures above.

If the coolant level is above the Full line, drain coolant so that the coolant level is between the Full and Low lines.


Hide 51420 6.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51410 7.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY