The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Note |
|---|---|---|---|---|---|
| P161A87 | Lost Communication with Alternator Missing Message | Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON (1 trip detection logic) |
·
Wire harness or connector
·
Generator assembly
·
ECM |
Charge warning is displayed | SAE: P161A |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before replacing the ECM, refer to Service Bulletin.
Check the charging system.
Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Stop and Start System) | A |
| OK (w/o Stop and Start System) | B |
| NG | C |
A
B
C
Disconnect the ECM connector.
Disconnect the generator assembly connector.
Disconnect the battery state sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B39,C53,C38)Location & Routingewd_type=routing;type=c,c,c;code=B39,C53,C38 |
||
| B39-2 (LIN) or C53-2 (LIN) - C38-17 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B39,C53,C38)Location & Routingewd_type=routing;type=c,c,c;code=B39,C53,C38 |
||
| B39-2 (LIN), C53-2 (LIN) or C38-17 (LIN) - Body ground | Ignition switch off (while LIN communication stopped) |
10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs using the GTS, and then write them down.
Clear the DTCs.
Turn the ignition switch off and wait 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Allow the engine to idle for approximately 17 minutes or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P161A87 is output | A |
| P161A87 and P162B87 are output | B |
| DTCs are not output | C |
A
for DENSO Made: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for DENSO Made)>REMOVAL
for VALEO Made: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for VALEO Made)>REMOVAL
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the ECM connector.
Disconnect the generator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C53,C38)Location & Routingewd_type=routing;type=c,c;code=C53,C38 |
||
| C53-2 (LIN) - C38-17 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C53,C38)Location & Routingewd_type=routing;type=c,c;code=C53,C38 |
||
| C53-2 (LIN) or C38-17 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for DENSO Made: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for DENSO Made)>REMOVAL
for VALEO Made: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>GENERATOR (for VALEO Made)>REMOVAL
NG