Home › Power Source / Network › V35A-FTS (BATTERY / CHARGING) › GENERATOR (for DENSO Made)
RM38G0E _57 Power Source / Network _101530 V35A-FTS BATTERY / CHARGING _0470504 GENERATOR(for DENSO Made) A

V35A-FTS BATTERY / CHARGING  GENERATOR(for DENSO Made)  REMOVAL  


CAUTION / NOTICE / HINT

A484911N01
6.698,0.688 6.865,0.688 false 1.594,1 1.844,1 false 5.5,3.75 5.667,3.75 false 5.167,4.281 5.333,4.281 false 0.542,1.833 0.75,1.833 false 6.646,0.292 6.813,0.292 false 3.802,3.271 3.969,3.271 false 1.198,5.417 1.448,5.417 false 1.823,3.188 1.99,3.188 false 5.24,5.354 5.354,5.354 false 3.51,4.167 3.667,4.167 false 4.719,3.875 4.927,3.292 4.927,3.292 5.01,3.292 false 6.51,0.573 6.792,0.927 0.281,0.354 18 false 1 1.302,0.844 1.583,1.198 0.281,0.354 18 false 3 5.417,4.167 5.698,4.521 0.281,0.354 18 false 8 0.802,1.083 1.135,1.229 0.333,0.146 10 false x 3 6.469,0.156 6.75,0.51 0.281,0.354 18 false 2 5.76,3.604 6.042,3.958 0.281,0.354 18 false 7 0.344,1.688 0.625,2.042 0.281,0.354 18 false 4 4.073,3.135 4.354,3.49 0.281,0.354 18 false 5 1.521,5.26 1.802,5.615 0.281,0.354 18 false 6 1.615,3.052 1.896,3.406 0.281,0.354 18 false 9 3.729,4.083 4.281,4.438 0.552,0.354 10 false *2 5.729,5.198 6.188,5.542 0.458,0.344 18 false 10 3.854,2.552 4.313,2.75 0.458,0.198 10 false x 3 4.198,3.969 4.656,4.167 0.458,0.198 10 false x 2 4.49,4.688 4.948,4.885 0.458,0.198 10 false x 2 4.052,4.438 4.51,4.635 0.458,0.198 10 false x 2 4.427,5.188 4.885,5.385 0.458,0.198 10 false x 2 2.896,3.76 3.354,3.958 0.458,0.198 10 false x 2 1.969,2.792 2.427,2.99 0.458,0.198 10 false x 2 5.083,3.198 5.396,3.396 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 FRONT WHEEL - - - -
4 FRONT FENDER APRON TRIM PACKING A 53782 - - -
5 ENGINE WIRE 82121 - - -
6 FAN SHROUD 16711 - - -
7 NO. 1 AIR TUBE ASSEMBLY - - - -
8 NO. 1 AIR HOSE 17341M - - -
9 WATER INLET PIPE 16322 - - -
10 GENERATOR ASSEMBLY 27060 (Click here) - -

*1 NO. 1 AIR TUBE SUPPORT *2 ENGINE WIRE

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


The necessary procedures(adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the generator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE FRONT WHEEL

Hide 53782 4.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 82121 5.DISCONNECT ENGINE WIRE

a.
A488275


Hide 16322 9.DISCONNECT WATER INLET PIPE

a.
A484870


Hide 27060 10.REMOVE GENERATOR ASSEMBLY

a.
A484873


b.
A484871C01
0.042,0.031 0.177,0.281 0.135,0.25 18 true i 2.958,0.052 3.094,0.313 0.135,0.26 18 true ii 5.115,0.052 5.313,0.323 0.198,0.271 18 true iii
V113147

Remove in this Direction - -


i.

Remove the 2 bolts and 2 nuts.


ii.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and generator assembly.


iii.

Remove the generator assembly as shown in the illustration.