Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY › 2021.04–2021.07
RM38G0E _52 Drivetrain _101647 DRIVE SHAFT / PROPELLER SHAFT _0470833 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C457898N02
2.354,0.823 3.094,1.031 0.74,0.208 2.313,0.771 3.135,1.073 0.823,0.302 4.667,0.313 5.51,0.521 0.844,0.208 4.625,0.26 5.542,0.563 0.917,0.302 1.448,4.802 2.115,5.021 0.667,0.219 1.75,4.052 1.927,4.448 1.927,4.448 2.094,4.448 false 3.979,2.042 4.323,2.896 4.323,2.896 4.573,2.896 false 2.188,1.344 2.188,0.927 2.188,0.927 2.354,0.927 false 4.5,1.021 4.5,0.427 4.5,0.427 4.667,0.427 false 1.438,4.917 1.271,4.917 1.271,4.917 1.271,4.5 false 5.688,4.635 5.917,5.25 5.917,5.25 6.167,5.25 false 4.948,2.76 5.229,3.115 0.281,0.354 18 false 1 2.167,4.333 2.448,4.688 0.281,0.354 18 false 2 2.26,1.292 2.719,1.49 0.458,0.198 10 false x 4 6.271,0.688 6.729,0.885 0.458,0.198 10 false x 4 1.375,4.354 1.833,4.552 0.458,0.198 10 false x 2 4.708,1.073 5.167,1.271 0.458,0.198 10 false x 4 4.469,1.094 4.927,1.292 0.458,0.198 10 false x 4 2.417,0.865 3.885,1.021 1.469,0.156 8 false 90 (918, 66) 4.74,0.344 6.458,0.5 1.719,0.156 8 false 88.3 (900, 65) 1.5,4.844 2.854,5 1.354,0.156 8 false 10 (102, 7) 6.229,5.125 6.51,5.479 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR PROPELLER SHAFT ASSEMBLY 37110F (Click here) - -
2 NO. 3 PROPELLER SHAFT HEAT INSULATOR - - - -
3 CENTER EXHAUST PIPE ASSEMBLY - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V103638

Do not apply lubricants - -

PROCEDURE

Hide 37110F 1.INSTALL REAR PROPELLER SHAFT ASSEMBLY

a.
C457904C02
5.719,1.073 5.51,1.438 5.51,1.438 5.75,1.104 true 2,1.115 1.823,1.49 1.823,1.49 2.031,1.177 true 5.396,1.458 5.615,1.656 0.219,0.198 10 true *a 1.729,1.5 1.948,1.698 0.219,0.198 10 true *a 0.406,0.042 1.188,0.479 0.781,0.438 18 true i, ii, iii 4.083,0.042 4.792,0.385 0.708,0.344 18 true i, iv, v
*a Matchmark - -


i.

Completely remove any oil, etc. and clean the contact surfaces of the 2 propeller shaft flanges, differential flange and transfer flange.


ii.

Align the matchmarks on the propeller shaft flange and transfer flange.


iii.

Install the rear propeller shaft assembly with the 4 nuts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


iv.

Align the matchmarks on the propeller shaft flange and differential flange.


v.

Install the rear propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

Torque:
88.3 N*m (900 kgf*cm, 65 ft.*lbf)



Hide 2.INSTALL NO. 3 PROPELLER SHAFT HEAT INSULATOR

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)