Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS)  P070312  Brake Switch "B" Circuit Short to Battery  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving in the lock-up condition.

When the brake pedal is depressed, the stop light switch assembly sends a signal to the TCM. The TCM then cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070312 Brake Switch "B" Circuit Short to Battery The stop light switch remains ON even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2-trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

TCM


Comes on DTC stored SAE: P0724

MONITOR DESCRIPTION

This DTC indicates that the stop light switch is remaining on. When the stop light switch remains on during GO and STOP driving, the TCM interprets this as a malfunction of the stop light switch, then illuminates the MIL and stores this DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order to store this DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Repeat the procedure below 5 times:

-

Drive the vehicle (vehicle speed is 30 km/h (18.65 mph) or more)

-

Stop the vehicle (vehicle speed is 3 km/h (1.86 mph) or less)


4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P070312.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

for LHD:
C403374E08
1.292,2.125 2.365,2.323 1.073,0.198 10 false Battery 3.51,1.688 4.604,2.198 1.094,0.51 10 false Stop Light Switch Assembly 5.542,2.802 6,3 0.458,0.198 10 false TCM 5.094,1 5.552,1.198 0.458,0.198 10 false 36 5.365,0.99 5.823,1.188 0.458,0.198 10 false STP 4.552,1 4.771,1.219 0.219,0.219 10 false 3 4.333,1.115 4.552,1.333 0.219,0.219 10 false L 3.719,1.115 3.938,1.333 0.219,0.219 10 false B 3.479,1 3.698,1.219 0.219,0.219 10 false 7 5.542,2.625 6,2.823 0.458,0.198 10 false C36 3.521,1.521 3.979,1.719 0.458,0.198 10 false B43 2.688,1.26 3.292,1.458 0.604,0.198 10 false STOP 1.635,1.26 2.24,1.458 0.604,0.198 10 false PDB-B

for RHD:
C377261E03
1.292,2.125 2.365,2.323 1.073,0.198 10 false Battery 3.646,1.688 4.74,2.198 1.094,0.51 10 false Stop Light Switch Assembly 5.542,2.802 6,3 0.458,0.198 10 false TCM 5.094,1 5.552,1.198 0.458,0.198 10 false 36 5.365,0.99 5.823,1.188 0.458,0.198 10 false STP 4.552,1 4.771,1.219 0.219,0.219 10 false 3 4.333,1.115 4.552,1.333 0.219,0.219 10 false L 3.844,1.115 4.063,1.333 0.219,0.219 10 false B 3.625,1 3.844,1.219 0.219,0.219 10 false 7 5.542,2.625 6,2.823 0.458,0.198 10 false C36 3.646,1.521 4.104,1.719 0.458,0.198 10 false B43 2.896,1.26 3.5,1.458 0.604,0.198 10 false STOP 2.167,1.26 2.771,1.458 0.604,0.198 10 false PDB-B 1.354,1.281 2.521,1.719 1.167,0.438 10 false MAIN R/B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
Powertrain > Transmission > Data List
Tester Display
Stop Light SW
50003 373 12
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

Stop light switch assembly is installed correctly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)
a.

Disconnect the stop light switch connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B43,C36)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

B43-3 (L) or C36-36 (STP) - Other terminals Always 10 kΩ or higher


HINT:

If there is a short in the STP terminal circuit, there may be a malfunction in the circuit of a connected ECU.



Result:
Proceed to
OK
NG



OK

4.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STOP LIGHT SWITCH ASSEMBLY

OK

5.REPLACE TCM

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY